05 May 2018 0 8K Report

I am going to make the HIT CELL Bi facial through AFORS HET Softwar so what changes i need to do so that it give me correct results

More Naveed Ahmad's questions See All
Can someone explain the attached graphs?

I place different doping on X axis and get the following curves of efficiency parameters can someone body explain its behavior that why this increase and decrease come

04 May 2018 1,702 4 View

With the addition of layer on solar panel why my short circuit current & Fill Factor get decrease?

i am adding ITO layer on crystalline silicon solar cell due to which my fill factor and short circuit current get decrease why this happen

01 February 2018 7,908 5 View

How to calculate the recombination and generation of HIT cell?

i am using AFORSHET software for simulation purpose now i need to improve my short circuit current for that i need to know about my generation and recombination so anybody tell me how i calculate it.

01 February 2018 1,557 3 View

No title

kindly answer this question

03 April 2017 294 1 View

In Suspended graphene SiO2 layer is removed by etching which eliminat charges in SiO2 and after annealing produce high quality graphene why?

plz answer instantly

03 April 2017 4,137 1 View

For which solar cell parameter is the upper limit set by the content of solar spectrum??

i think its short circuit current because short circuit current depend on the no of irradiation and their energy if higher energy and their content then higher will be the short circuit current...

11 December 2016 6,733 0 View

Similar questions and discussions
Timeout error!! Processor in the loop (PIL) using STM32F4 Matlab 2018a?

Dear Researchers I am trying to perform a PIL simulation using STM32F4 Discovery board and comunication serial USB TO TTL. During simulation I receive the following timeout error: An error...

01 March 2021 2,327 1 View

No title

I am trying to find how to know the density needed for a pva electrospinning in a 0.6mm neddle, the electrospinning will be from top to bottom and the problem I really have is the solution because...

25 February 2021 2,615 3 View

How Can I clain a removal of a co-author?

I would like to make a correction in a co-author in your paper which is wrong. This name is also in other papers of Kenton Ko. Zey Ko is not a Co-author . The correct name is Zdenka...

24 February 2021 3,476 4 View

How does the injection volume impact LLOQ and ULOQ in regression analysis (LC-MSMS)?

Hello, I have run into an issue that has sparkled a debate at work: is the LLOQ/ULOQ impacted by injection volume under the following circumstances: 1) Same dilution factor of all samples 2)...

23 February 2021 9,159 3 View

Difficulty in debugging code to correct error - TypeError: '<' not supported ?

I am trying with a Unet code ontained from net ...in tensorflow. When trying to predict the segmentation result with the trained and saved model with metric " iou" using "CustomObjectScope"...

22 February 2021 5,254 1 View

How to perform Haldane correction on SPSS?

I was wondering if anyone knew how to perform the Haldane correction for SPSS (this is the definition of the correction -...

21 February 2021 2,882 1 View

absorption= 1-mag(S(FP1:1,FP1:1)*S(FP1:1,FP1:1))-mag(S(FP2:1,FP1:1)*S(FP2:1,FP1:1)) is it correct for absorption ?

hi everyone I am simulating a unit cell structure in HFSS using Flouquet port having two modes for absorption I have used this formula:- absorption=...

17 February 2021 9,178 2 View

How can I calculate the magnetic force applied from a magnet (no electrism)?

I would like to calculate the magnetic force on a Fe304 particle which is into a liquid solution . The magnet is above the solution , and there is no electricity. I found this formula : F = (V...

13 February 2021 4,770 3 View

What is the best way to do symmetry in ANSYS Fluent for flow between two concentric cylinders ?

I am working on Taylor Couette flow between concentric cylinders and the results are correct for the full case. however, I wanted to do symmetry case to improve the mesh. I have tried periodic...

11 February 2021 2,193 6 View

What is the ideal value of UACI for image encryption scheme?

UACI - Unified Averaged Changed Intensity between cipher images. Why some papers refer ideal value to be 33.33 and some refer it to be 33.46? Which is the correct value? (In reference to image...

11 February 2021 9,562 2 View

Our partners will collect data and use cookies for ad personalization and measurement. Learn how we and our ad partner Google, collect and use data. Agree & close