When should I use remote force/displacement on ANSYS workbench, and why is it giving more accurate result in case of a beam?

Sitangshu Chatterjee @Sitangshu_Chatterjee3

05 May 2018 1 7K Report

The problem to be simulated is described in the picture. I am looking to find stress at A.

Badges
Science topic

More Sitangshu Chatterjee's questions See All

What are steps and formulae (with derivations, preferably) required to design a cantilever snap-fit?

I want to design a cantilever snap-fit as a component for my project. However, I have not found the steps anywhere in any texbook or on the internet (not a great searcher I guess). Can someone...

08 September 2018 7,905 1 View

Where (link) can I download the ANSYS workbench's user manual (pdf/ppt) for structural?

I have a subscription, but I cannot seem to find the link.

06 July 2018 4,863 3 View

ANSYS Workbench- Analysis of an open and ground ended spring subjected to axial load- anomalies between theoretical and simulation results. Why?

Hello altruists! So, I am trying my hand at some basic structural simulation at ANSYS WB, and I was trying to simulate the compression of a spring as in a shock absorber. I have attached the...

05 June 2018 8,275 3 View

Why is ANSYS not giving correct result for Normal Stress or Von-Mises Stress for a cantilever cylindrical beam subject to axial force ?

Hello people. I am new to FEA, and using Ansys to solve a few textbook problems to validate the solution. Please bear with me as the doubts might sound trivial. So, I am trying to simulate the...

04 May 2018 8,259 5 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

How to define and get results (stresses) for certain points of a model in abaqus, using python? When the size of the model changes?

I want to do a parameter study of a aixsymmetric cylinder in Abaqus. I want to create several jobs where I get the stresses for 3 different points in my model. These points are defined. I wrote a...

01 March 2021 10,078 1 View

LOAD DISPLACEMENT CURVES Stiffness increasing in ANSYS non linear analysis. HOW CAN I CORRECT IT?

Hi. I am doing non linear FE analysis using a new material beam under flexural 2 point loading using ANSYS. I have defined a bilinear material model. The solution has converged. In results I am...

01 March 2021 9,911 3 View

In Molecular Dynamics Simulation, how do I make changes to the force field according to my protein?

Hi In Molecular Dynamics Simulation, how do I make changes to the force field according to my protein? I got this error in the add-ion stage: Fatal error "./ amber99sb-ildn-HHH.ff / force...

01 March 2021 8,747 4 View

How to show arrows over the streamlines in CFD-post?

I follow this to make streamlines like the photos attached below: (software- CFD post-processing) First I plot the 2D streamline over a surface "streamline 1". them I plot a vector by the...

01 March 2021 8,668 3 View

Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS?

I need to model masonry and reinforced concrete minarets for my MSc thesis. Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS? (Or any other program for just...

01 March 2021 736 3 View

Can Virtual Servers (remote dekstop manager) run heavy ANSYS Fluent CFD simulation ?

I have a virtual machine. My host Pc specs are not that good thats why i went for virtual servers. so basically my host pc has 8gb of ram with nvidia quadro k2200 4Gb DDR5 GPU ,processor intel...

01 March 2021 8,415 1 View

How to increase mesh quality of a cfd model in ansys fluent?

How can one improve mesh skewness, orthogonality, aspect ratio?

28 February 2021 7,730 3 View

How can we simulate an hyperelastic-viscoelastic behavor with Ansys APDL?

I am working on modeling and simulation of biomecanical material behaviour, I have succeded on simulating skin using anisotropic hyperelastic material, on APDL and in our lab's finite element...

28 February 2021 552 3 View