When I change the primary phase from a single component to multicomponent in Fluent, does the flow field change or get modified?

More Lister Herington Falleiro's questions See All

How to debug this error i am getting in Fluent " there must be more than 1 species on each phase"?

I am using multi-phase Eulerian granular model. I have activated the species model. I am trying to find layering on a solid surface from the bulk solution. I am having 2 phases ( 1 liquid phase +...

11 January 2018 2,014 2 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

How to show arrows over the streamlines in CFD-post?

I follow this to make streamlines like the photos attached below: (software- CFD post-processing) First I plot the 2D streamline over a surface "streamline 1". them I plot a vector by the...

01 March 2021 8,668 3 View

What is recommended for solid domain in ANSYS FLUENT?

Should I mesh the solid domain ? or should I use wall thickness? or Shell conduction? for Heat Transfer between two fluids of a Heat Exchanger. what is recommended?

01 March 2021 9,785 3 View

Can Virtual Servers (remote dekstop manager) run heavy ANSYS Fluent CFD simulation ?

I have a virtual machine. My host Pc specs are not that good thats why i went for virtual servers. so basically my host pc has 8gb of ram with nvidia quadro k2200 4Gb DDR5 GPU ,processor intel...

01 March 2021 8,415 1 View

How to increase mesh quality of a cfd model in ansys fluent?

How can one improve mesh skewness, orthogonality, aspect ratio?

28 February 2021 7,730 3 View

How do you mesh a thin solid in Fluent?

Hello, I have used the shell function on SpaceClaim to create thin solids for the model I am studying. These are contained within an enclosure for my study. I chose this approach as it avoids the...

24 February 2021 8,856 3 View

How to extract the y+ value from fluent ?

I am doing a 3D steady simulation of a wind rotor using Ansys Fluent. In order to have a y+ of 1, I created 10 inflation layers using total layer thickness method, and I started a first...

23 February 2021 2,819 3 View

Help with assigning pressure boundary conditions in FLUENT on a large structure?

Hello, I created a very tall tower (>1000m) and applied pressure boundary conditions at the inlet (bottom) and outlet (top) that correspond to the pressure are their relative altitudes....

22 February 2021 9,972 4 View

How do I add a udf to Ansys fluent and does it need to be compiled before hand ?

I have a Define_CG_Motion udf written in c where do I add it to my Ansys fluent project and does it need to be compiled before that?

21 February 2021 9,347 3 View

How do I plot Pressure against crank angle degree in Fluent?

18 February 2021 8,390 3 View

Manmatha Roul Popular answer

Yes, by changing the primary phase from a single component to multicomponent in Fluent, the flow field gets modified.

So, you have to run the simulation after initializing the flow field.

Ehsan Asgari

Hi Lister,

AFAIK, the velocity and pressure fields should not change because in species transport mode, only a single set of continuity and momentum equations is solved for all species.

Regards,

Ehsan

Carlos Moreno Negrin

Hi, Lister.

Independently from the software you use, when you change the primary phase for multicomponent, the properties of the fluid would change (viscosity for instance), just like other transport properties. So, the pressure and velocity fields would also be modified.

Best Regards..

Lister Herington Falleiro

thank you Carlos Moreno Negrin and Ehsan Asgari for your reply.