When doing biological cell migration, can electrode be connected directly to agar bridge, or does it need to be immersed in salt solution?

Anubhav Bussooa @Anubhav_Bussooa

10 October 2017 1 7K Report

Does the electrode need to be of a specific metal?

Which salt solution and concentration to use?

Hussam Ali Mohammed

Interesting..

Badges
Science topic

More Anubhav Bussooa's questions See All

Can SiO2 deposition be used to protect gold electrodes (in direct contact with ionic solution) from electrolyis?

Will the electrodes remain conductive? What should be the thickness of SiO2 deposition?

03 April 2018 3,009 3 View

When electrolysis occurs, does the anode or cathode heat up more (or by same extent)?

Does it depend on the relative size of the electrodes?

01 February 2018 9,696 4 View

How can I protect thin film (30nm) gold electrodes from electrolysis?

I apply voltage (AC, DC and pulse) to biological cell monolayers using 30nm thick gold electrodes. My observations are significantly affected by electrolysis (formation of gas bubbles). Moreover,...

01 February 2018 8,075 6 View

Is it possible to use trypan blue to stain a cell monolayer?

I wish to determine live/dead cell ratio while the cells are still in a monolayer

07 August 2017 3,949 1 View

Can a gold pattern on glass slide work as inductive coil?

If so, what is the most appropriate pattern shape and gold thickness?

06 July 2017 539 3 View

Is it possible to fabricate gold electrodes on pdms? what adhesion layer or pdms surface treatment is required?

will the electrodes withstand bending?

01 February 2017 8,992 1 View

Is there a reliable way of "visualising" an electric field between 2 planar electrodes?

My electrodes are 2 bands of gold with a gap in between || Is there any way of making sure an electric field exists between the electrodes?

09 October 2016 3,576 6 View

What is the physiological shear stress on mouse endothelial cells?

i would like to carry out flow experiments to determine how culture medium flow affects cell morphology

01 January 1970 6,742 4 View

What is the reason for current dropping in OER , LSV curve?

I tried four trials of the same Copper Phosphides sample in Alkaline medium ( 0.5M KOH) with Hg/HgO reference electrode and Pt as counter electrode. I used 0.001 V/s scan rate for first three...

10 August 2024 3,629 1 View

Basis set and input instruction to calculate HOMO and LUMO using Orca for Imidazolium based organic salts?

Hey there, As a synthetic chemist delving into theoretical calculations for my imidazolium-based organic molecules, I would greatly appreciate any guidance on the appropriate input instructions...

09 August 2024 5,444 7 View

Why Do TDS and EC Increase with Larger Wastewater Volumes, While BOD and COD Decrease?

I have carried out MFC experiments on three different volumes, 50, 500 and 1000 mL of wastewater. Results after MFC treatment shows that TDS and EC are more in larger volumes of water i.e. TDS and...

09 August 2024 9,621 0 View

Could it be a cell culture contamination?

Hello everyone! I observed in my culture (htert-RPE1 cells) an orange- red particle at the bottom of the dish. It is visible to the naked eye as a very very small red dot. Could it be a...

09 August 2024 2,824 3 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

Is there any way to quantify bacterial and fungal cells in their mixed culture?

I am working in fungal fermentation of soybean meal and there is bacterial growth in them at times. I am trying to quantify fungal cell counts and bacterial cells; but I haven't been able to do at...

07 August 2024 7,535 4 View

How to normalize and take the significance of the MTT OD values with 3 replicates for the same cell-line?

Hi, I have a question about normalizing the MTT OD values for doing the statistical analysis. So, if we have 3 different plates and we call them 3 different replicates, so, first we would...

07 August 2024 8,106 4 View

Why activated CAR-Jurkat cell could not kill targets?

Previously when I co-coluture anti-CD19(FMC63) CAR-Jurkat with Raji with E:T=5:1, Jurkat can eliminate Raji in 24h. However, when I test another CAR construct, although I can dectect totally CD69...

06 August 2024 641 2 View

How to isolate lymphocytes from mouse spleen?

I have tried several times to isolate lymphocytes from mouse spleen, but all attempts have been unsuccessful. I tried most available protocols. I used different dissociation media (HBSS with Ca...

04 August 2024 9,913 7 View

How to Add Missing Water Molecules in Protein-Membrane Simulations?

I have protein-membrane simulations (PDB, PSF, DCD) and have noticed that water molecules near the protein are not visible in the simulations. How can I fix this issue? Is there a way to place the...

04 August 2024 1,200 2 View