What's the density conversion factor expressed in cm3liq/cm3gas for CO2?

01 January 2014 0 452 Report

I measured the CO2 adsorption isotherms and I need to convert the maximum capacity (isotherm ordinate) expressed as cm3 CO2 (gas)/g adsorbent in cm3 CO2 (liq)/g adsorbent. I suppose this is the right conversion to apply, am I right?

Badges
Science topic

More Antonio Salituro's questions See All

Can the Time weighted average (TWA) exposure concentration be estimated starting from the Short-Term Exposure Limit (STEL)?

Hello, I have got an MSDS indicating the STEL of a compound and I'd like to know what the relevant TWA would be. Is there a general ratio which roughly links the two parameters (regardless of the...

31 December 2019 4,567 4 View

Could anybody provide a reference on the X-ray diffraction pattern of silicon?

Hello, I am after a paper reporting the X-ray diffraction pattern of silicon, possibly including all the diffraction peak positions. Thanks, Antonio

09 October 2019 9,754 4 View

How is water activity of pharmaceutical products measured?

Hello All, Which methodology should I follow to measure water activity of pharmaceutical materials? I am aware that there are two USP procedures in this regard, chapter 922 and 1112. Which of...

04 May 2019 4,294 5 View

How can I calculate the time per step if scan range, scan speed and step size are known?

Hello All, I am trying to reproduce an XRD method. I know scan range, scan speed and step size. How do I work out the time per step? Thanks, Antonio

05 June 2018 423 8 View

Could anybody provide references to water vapour pressure data at 25deg for the saturated solutions of the following salts?

I am just looking for references on water vapour pressures for the saturated solutions of the following salts: LiBr LiCl MgCl2 Mg(NO3)2 NaCl KCl KNO3 I have found the following reference...

02 March 2018 8,469 2 View

Could anybody suggest any (possibly pharmaceutical) material which could be used for PXRD proficiency testing?

I would like to fin out more information about which type of material (ideally pharmaceutical compounds) could be suitable to perform both qualitative and quantitative Powder X-ray diffraction...

31 December 2017 2,667 10 View

Could anybody suggest how to calculate the heat of adsorption/desorption from heat flow data (DSC) in mW?

Hi, I have got some DSC data related to the heat flow in mW (milliWatt I presume?) measured during adsorption/desorption of CO2 onto/from an activated carbon. I'm getting some inconsistent...

05 June 2015 3,089 5 View

Could anybody advise about the demineralization procedure of activated carbons?

Hi All, I'd need to remove inorganic fractions (especially Ca-based ones) from my carbons. What's the typical procedure to apply in order to do that? I'd like to know the main conditions (acid...

01 February 2015 9,319 4 View

Could anyone recommend any companies in UK to purchase activated carbons from?

I'd need to purchase some activated carbons. Ideally, I would need two different type of products, a carbon having high micropore volume (d

06 July 2014 2,388 2 View

Has anybody been to any previous editions of the EUEC (Energy, Utility & Environment Conference)?

I'm planning to go to this year's edition in San Diego. It looks like a big event. My project is about CO2 capture so it kind of fits quite well in there. However, it would be nice to get some...

06 July 2014 2,762 1 View

I have get this error when i calculated the geometrical optimization for prco3, it takes 12 hours until gives this message in the outputfile?

Fatal error in MPI_Allreduce: Other MPI error, error stack: MPI_Allreduce(1628)......: MPI_Allreduce(sbuf=000002459254A180, rbuf=000002459F86A140, count=4851, MPI_DOUBLE_COMPLEX, MPI_SUM,...

09 August 2024 7,615 1 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

Hello Everyone ! I'm looking for a good journal to publish my manuscript with low publication cost?

I am Looking for a Science Journal with good impact factor and low publication cost to publish a review paper. Your suggestions would be appreciated.

06 August 2024 6,796 3 View

Why does my protein refolded to beta sheet during thermal denaturation analysis?

Hi! So i attempted to understand a novel protein behavior towards heat application by analyzing its secondary structure change. I subjected the protein to a thermal denaturation analysis using...

06 August 2024 1,989 3 View

What is the prepared reference material that can be used in inductively coupled plasma optical emission spectrometry (ICP-OES) to measure REE and U ?

What is the prepared reference material that can be used in the ICPE-9820 Shimadzu Japan instrument, which employs inductively coupled plasma optical emission spectrometry (ICP-OES) to measure...

06 August 2024 1,896 1 View

Absorption coefficient of methane?

Hello, Can anyone provide me with the absorption coefficient of methane gas at 7.7 um? Any reference?

06 August 2024 980 5 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

How effective is the Citi Bloc standard basket in enhancing the accuracy and comparability of international construction cost assessments?

Citi BLOC Standard Basket Definitions: A standardized unit representing a fixed basket of construction materials, labor, and equipment costs priced in various cities. Purpose: To create a common...

04 August 2024 8,997 1 View

Any idea about 'International Research Journal of commerce , arts and science? Is it a UGC listed journal?

Any idea about 'International Research Journal of commerce , arts and science? Is it a UGC listed journal? Kindly advice

04 August 2024 7,367 3 View

Are authors sowing for scientific Journals to be reaping the benefits? We are charged for publication but we offer free peer review services, why?

As authors and academic writers, we usually prepare our manuscript using our own resources. We submit these manuscripts to scientific Journals for peer review and publication sometimes at a fee....

03 August 2024 7,304 2 View