Could anyone recommend any companies in UK to purchase activated carbons from?

More Antonio Salituro's questions See All

Can the Time weighted average (TWA) exposure concentration be estimated starting from the Short-Term Exposure Limit (STEL)?

Hello, I have got an MSDS indicating the STEL of a compound and I'd like to know what the relevant TWA would be. Is there a general ratio which roughly links the two parameters (regardless of the...

31 December 2019 4,567 4 View

Could anybody provide a reference on the X-ray diffraction pattern of silicon?

Hello, I am after a paper reporting the X-ray diffraction pattern of silicon, possibly including all the diffraction peak positions. Thanks, Antonio

09 October 2019 9,754 4 View

How is water activity of pharmaceutical products measured?

Hello All, Which methodology should I follow to measure water activity of pharmaceutical materials? I am aware that there are two USP procedures in this regard, chapter 922 and 1112. Which of...

04 May 2019 4,294 5 View

How can I calculate the time per step if scan range, scan speed and step size are known?

Hello All, I am trying to reproduce an XRD method. I know scan range, scan speed and step size. How do I work out the time per step? Thanks, Antonio

05 June 2018 423 8 View

Could anybody provide references to water vapour pressure data at 25deg for the saturated solutions of the following salts?

I am just looking for references on water vapour pressures for the saturated solutions of the following salts: LiBr LiCl MgCl2 Mg(NO3)2 NaCl KCl KNO3 I have found the following reference...

02 March 2018 8,469 2 View

Could anybody suggest any (possibly pharmaceutical) material which could be used for PXRD proficiency testing?

I would like to fin out more information about which type of material (ideally pharmaceutical compounds) could be suitable to perform both qualitative and quantitative Powder X-ray diffraction...

31 December 2017 2,667 10 View

Could anybody suggest how to calculate the heat of adsorption/desorption from heat flow data (DSC) in mW?

Hi, I have got some DSC data related to the heat flow in mW (milliWatt I presume?) measured during adsorption/desorption of CO2 onto/from an activated carbon. I'm getting some inconsistent...

05 June 2015 3,089 5 View

Could anybody advise about the demineralization procedure of activated carbons?

Hi All, I'd need to remove inorganic fractions (especially Ca-based ones) from my carbons. What's the typical procedure to apply in order to do that? I'd like to know the main conditions (acid...

01 February 2015 9,319 4 View

Has anybody been to any previous editions of the EUEC (Energy, Utility & Environment Conference)?

I'm planning to go to this year's edition in San Diego. It looks like a big event. My project is about CO2 capture so it kind of fits quite well in there. However, it would be nice to get some...

06 July 2014 2,762 1 View

What is the best technique for investigating the presence of CaO in a solid sample?

I've seen from the literature that XRF gives results in terms of oxides (e.g. CaO). Is this correct? What's the difference in terms of chemical composition results between XRF, XRD and EDX?

05 June 2014 803 15 View

What is the reason for current dropping in OER , LSV curve?

I tried four trials of the same Copper Phosphides sample in Alkaline medium ( 0.5M KOH) with Hg/HgO reference electrode and Pt as counter electrode. I used 0.001 V/s scan rate for first three...

10 August 2024 3,629 1 View

Adhesion strength of coating?

How can I determine a good adhesion strength range for coatings on polymer surfaces, such as DLC on polymer substrates? Is there a specific threshold for adhesion strength (from T-peel tests)...

10 August 2024 942 3 View

Do interactions between biosphere, carbon cycle, & water cycle impact global warming & interaction between atmosphere & hydrosphere?

How do interactions between the biosphere, the carbon cycle, and the water cycle impact global warming and interaction between the atmosphere and the hydrosphere?

09 August 2024 3,291 2 View

Who of all of you will help TPEOM to re-originate the Earths atmosphere to it original 5 atmospheric elements/gases?

Global ‘Weather’ has stopped, as ‘aqua thermionic instituted by the ‘Global thermo atmospherics has instituted global thermodynamics of 120º C + and thus all waters are, or have boiled into a...

06 August 2024 8,716 0 View

How can I separate graphene from amorphous carbon of similar particle sizes?

The starting material is a finely ground powder. Some particles contain more graphene than others.

30 July 2024 3,978 2 View

Question about combustion Kinetics ?

I am currently working on modeling FCC catalyst regeneration and have come across a point of uncertainty that I hope you can assist me with. In my previous models, I have utilized lumped kinetics...

30 July 2024 6,137 0 View

What are the perfect mathematical model for a solar-powered ship implementation?

A computational study of heat flux on cylindrical surfaces using CNT hybrid nanofluids

28 July 2024 4,985 1 View

Why semicircle of nyquist plot is not complete?

While I am doing HER, I noticed that nyquist plots of Electrochemical Impedance Spectroscopy (EIS) is not complete. Will it affect for the Linear Sweep Voltametry (LSV) data? However, I can found...

26 July 2024 7,542 4 View

What is the impact of collaborations with key suppliers on an SME's competitiveness?

The literature on Supply Chain Integration (SCI), Supply Chain Management (SCM), and collaborations, spanning several decades, deserves special attention. This topic, although addressed for a long...

23 July 2024 5,672 3 View

What is the principle/mechanism behind aging of carbon (graphite) containing refractory mix for isostatically pressed refractories?

The resin bonded carbon containing refractories are aged before use. How time of aging is determined? And mechanism behind aging.

23 July 2024 3,205 0 View

John Christopher Whitehead

AAC Eurovent Ltd

Registered Company Address

Unit K, Maybrook Industrial Estate, Maybrook

Road, Brownhills, WS8 7DG, England

Qamar Abbas

Did you get a carbon with pore size lower than 0.7nm, if yes, please share the name of the company-- apparently its hard to get such carbon--