I'm planning to go to this year's edition in San Diego. It looks like a big event. My project is about CO2 capture so it kind of fits quite well in there. However, it would be nice to get some feedback if possible.
Btw, that's the link..http://www.euec.com/
Hello, I have got an MSDS indicating the STEL of a compound and I'd like to know what the relevant TWA would be. Is there a general ratio which roughly links the two parameters (regardless of the...
31 December 2019 4,567 4 View
Hello, I am after a paper reporting the X-ray diffraction pattern of silicon, possibly including all the diffraction peak positions. Thanks, Antonio
09 October 2019 9,754 4 View
Hello All, Which methodology should I follow to measure water activity of pharmaceutical materials? I am aware that there are two USP procedures in this regard, chapter 922 and 1112. Which of...
04 May 2019 4,294 5 View
Hello All, I am trying to reproduce an XRD method. I know scan range, scan speed and step size. How do I work out the time per step? Thanks, Antonio
05 June 2018 423 8 View
I am just looking for references on water vapour pressures for the saturated solutions of the following salts: LiBr LiCl MgCl2 Mg(NO3)2 NaCl KCl KNO3 I have found the following reference...
02 March 2018 8,469 2 View
I would like to fin out more information about which type of material (ideally pharmaceutical compounds) could be suitable to perform both qualitative and quantitative Powder X-ray diffraction...
31 December 2017 2,667 10 View
Hi, I have got some DSC data related to the heat flow in mW (milliWatt I presume?) measured during adsorption/desorption of CO2 onto/from an activated carbon. I'm getting some inconsistent...
05 June 2015 3,089 5 View
Hi All, I'd need to remove inorganic fractions (especially Ca-based ones) from my carbons. What's the typical procedure to apply in order to do that? I'd like to know the main conditions (acid...
01 February 2015 9,319 4 View
I'd need to purchase some activated carbons. Ideally, I would need two different type of products, a carbon having high micropore volume (d
06 July 2014 2,388 2 View
I've seen from the literature that XRF gives results in terms of oxides (e.g. CaO). Is this correct? What's the difference in terms of chemical composition results between XRF, XRD and EDX?
05 June 2014 803 15 View
Hello everyone, I recently submitted an article to Geotechnical Engineering (Proceedings of the ICE), and the current status has been listed as "EiC Pre-assessment: Ready" for the past 20 days. I...
10 August 2024 6,493 1 View
How to develop investments in renewable energy sources?
08 August 2024 5,112 3 View
A fungal strain was treated with nanoparticles. We want to do an environmental SEM analysis. So could anyone share your views on preparing the sample? Thank you.
07 August 2024 5,307 1 View
Reference dose and Maximum acceptable concentrations HMs
03 August 2024 8,230 4 View
IEEE Conference template
02 August 2024 8,762 2 View
I am attempting to conjugate PEG to an amino acid at the C-terminus, for the purposes of producing nanoparticles. I have been told that PEG modified with amine groups can be used for this purpose,...
31 July 2024 2,033 1 View
AI-driven technologies offer previously unheard-of capabilities to process enormous volumes of data, extract insightful knowledge and improve predictive models, according to the UN’s World...
31 July 2024 9,733 3 View
Hello. Thanks for your consideration to see my question. Recently, I conducted XPS anaylsis of g-CN that is prepared from thermal polycondensation of DCDA, so-called conventional bulk-g-CN,...
30 July 2024 9,824 2 View
What should a Mechanical Engineering PhD scholar focus on during their PhD to enhance their chances of securing a postdoctoral position?
29 July 2024 7,714 4 View
In some data sources it has been grouped in Q1 and some shows it is Q2.
29 July 2024 4,227 2 View