What would be the optimum temperature for decellularization of Umbilical cord?

10 February 2023 1 4K Report

Actually i am decellularizing the human umbilical cord tissue using SDS detergent? What temperature would be best either at 4 degrees or at room temperature? Because the product i need is ECM.

Thanks

Kumar Chokalingam

Hi Tayyaba sharing you a protocol for UC decellularization Article Development of human umbilical cord based scaffold for tissu...

Badges
Science topic

More Tayyaba Bari's questions See All

Is there any method a part from centrifugation to remove air bubbles during the 3D printing of bioscaffolds?

I am fabricating the bioscaffolds from my bioink, The problem is each time I added my bioink in the syringe, it gets bubbles, which creates a hindrance during extruding and printing. I have used...

25 March 2024 6,163 0 View

Is it possible to bioprint with only collagen without using any other polymer and cross-linkers, if yes, what should be the voscosity?

I want to bio print a structure with collagen but i am not sure about the viscosity of that solution.

10 February 2024 6,577 1 View

How to solubilize the decellularized Umbilical Cord Tissue for Bioink?

I have decellularized the umbilical cord with detergent based methods, the problem is that I am unable to solubilize it with pepsin and HCl, kindly guide me with the exact protocol of...

01 June 2023 829 2 View

Why I can't see any band in SDS-PAGE?

Currently, when I run SDS-PAGE, I don't see any bands at all, even though I used the same material just a day ago and it worked fine.... In our lab, we dilute the 10X running buffer to 1X and...

06 August 2024 5,371 2 View

How to preform densitometry on SDS-page bands?

I ran a SDS-page of a bacterial lysate and I want to quantify protein concentration in a specific band. I was thinking of using a standards ladder or make some standards are different...

05 August 2024 9,803 3 View

For the process of preparing decellularized matrices what is the ideal solution in which we can bring the tissue from slaughter house to lab?

I am planning to prepare a decellularized porcine tissue derived biomaterial. It would be very helpful if I get to know the composition of the solution which is ideal to bring the tissue sample...

31 July 2024 5,645 2 View

Following click reaction in cell lysates, protein is immobile and remains at the top of the gel in SDS-PAGE?

I am using CuBr/THPTA for a click reaction in total cell lysates. I am facing issues with my protein sample in non-reducing SDS-PAGE where it's not migrating properly and most of it remains at the...

29 July 2024 949 4 View

Why my IgG antibody looks fragmented on non-reducing SDS-PAGE?

I am performing IgG purification and I have to show my results on SDS-PAGE. I use 10% tris glycine gel and prepare the samples under non reducing conditions. I am new to antibodies and therefore...

23 July 2024 6,662 6 View

What is the cause of this aggregation just bellow 70 kDa mark?

Hello, I was running a 12% SDS Page electrophoresis on few granulosa cell samples and got this result after the ponceau staining. The total protein lysate seem to aggregate at 70 kDa ladder mark...

21 July 2024 5,128 4 View

Anybody can assist me in Protein and magnetic beads seperation?

Hi, I hope you are doing well, I am working to remove DNA from protein sample by using silica hydroxode magnetic beads. I used different binding buffers but I din't get my protein band in initial...

02 July 2024 5,501 4 View

How accurate is Image J for SDS bands analysis?

I want to check my protein expression but the sample (target protein) on my SDS PAGE shows a little difference as compared to the control. I measured the band density through IMAGE J but the band...

01 July 2024 1,841 3 View

How to troubleshoot error E1 on Biorad Powerpac Basic despite using sufficient and fresh buffer?

I have used this BIorad Powerpac Basic for 4 years now, before which it was used for another 5-6 years. Generally we addressed the E1 error by compensating with fresh buffer and/or filling the...

01 July 2024 7,104 1 View

fluorescent imaging without fixatives?

How to store SDS-PAGE for fluorescent imaging without fixatives? I am running protein samples on SDS-PAGE that are tagged with fluorophores. If I place the gel in a destain solution of...

29 June 2024 8,720 1 View