Which plagiarism software is suitable for checking a paper before publication ?

Want to publish a research paper. I want to check plagiarism before publishing.

31 December 2017 8,604 7 View

Which type (Chemical Composition) of filler metal is suitable for Copper to Mild Steel and Mild steel to mild steel brazing joint ?

We are currently using 20% silver (Ag: 20%, Cu: 45%, Zn: 35%) brazing filler metal to join (Brazing joint) following combination - 01. Copper tube (6 mm) to copper coated Mild Steel tube (8...

31 December 2016 1,427 0 View

What are the suitable (best) Journals for publishing Articles on failure analysis?

we have completed failure analysis of an evaporator tube failure of a refrigerator. now we want to publish.

01 February 2016 4,315 1 View

Could you please inform me that how long at least I should perform the SALT SPRAY TEST on Aluminum evaporator tube to get so?

31 December 2015 3,715 13 View

How to draw trend line using Origin Lab/ OriginPro 9 ?

31 December 2015 8,659 1 View

Why can't make aluminum nitride film successfully by use sputter?

We use reactive sputtering process to make aluminum nitride film, and want to make c-axis aluminum nitride film on a silicon substrate, but the crystal orientation cannot be seen with...

03 March 2021 7,975 3 View

Sutter electrode holder leaking after applying positive pressure. How to fix?

I am using a Sutter electrode holder for my patch clamp experiments, but I'm having trouble keeping positive pressure inside my electrode due to a leak out of the back of the holder. I have added...

02 March 2021 5,829 1 View

What thickness need for ITO to use as conductive layer?

I want to do RF sputtering of ITO on glass substrate using magnetron sputtering. what thickness do i need to make it good conductive layer to use it for PSC. Moreover, whats about thickness of...

01 March 2021 395 3 View

How to check the uv-vis absorption of nanoparticle by surface plasmon resonance?

I try to check the uv-vis absorption of Indium nanoparticle. Now I am measuring in solution, can I measure it in the form of a film?

01 March 2021 930 3 View

1 nm thick MgO thin-film to be deposited on Si wafer using thermal evaporation. What will be the optimum deposition conditions?

Favourable conditions of base pressure, rate of deposition. Also, by which characterisation technique to be used to verify the thickness of the deposited film.

28 February 2021 3,640 3 View

Why is my platinum counter electrode getting dirty during electrodeposition?

I am conducting anodic electrodeposition of MnO2 onto a stainless steel substrate, using a platinum strip as a counter electrode. This is done galvanostatically, with the current held between 5...

27 February 2021 1,829 3 View

How does charge on working electrode changes with rising potential?

During performing CV of a GCE or modified GCE, we rise the potential in the first half of the cycle and reduce it in reverse half. During the first half, what is the nature of charge on GCE or...

25 February 2021 7,994 3 View

How to prepare a thin polymer film by post-polymerization/crosslinking?

24 February 2021 2,362 5 View

How to delaminate copper in water-based anodes?

Hello everyone, I'm looking for a way to delaminate copper current collector of water-based anodes in Li-ion batteries without damaging the graphite film. I tried different materials such as HNO3...

24 February 2021 3,785 3 View

Is is possible to pole with corona poling pellets of the sample material instead of thin films?

As it is highly probable that pellets will have a higher degree of air gaps and voids than thin films, is it possible to pole the samples with corona poling nevertheless? Or is there the...

24 February 2021 1,349 1 View