Which plagiarism software is suitable for checking a paper before publication ?

Want to publish a research paper. I want to check plagiarism before publishing.

31 December 2017 8,604 7 View

Which type (Chemical Composition) of filler metal is suitable for Copper to Mild Steel and Mild steel to mild steel brazing joint ?

We are currently using 20% silver (Ag: 20%, Cu: 45%, Zn: 35%) brazing filler metal to join (Brazing joint) following combination - 01. Copper tube (6 mm) to copper coated Mild Steel tube (8...

31 December 2016 1,427 0 View

What type of substrate is best to electrodeposit copper oxide thin film and measure optical transmittance ?

01 February 2016 4,455 7 View

What are the suitable (best) Journals for publishing Articles on failure analysis?

we have completed failure analysis of an evaporator tube failure of a refrigerator. now we want to publish.

01 February 2016 4,315 1 View

Could you please inform me that how long at least I should perform the SALT SPRAY TEST on Aluminum evaporator tube to get so?

31 December 2015 3,715 13 View

Can I put a figure that was drawn by Bio-Render in publication paper?

I want to publish paper in journal but I have figures which have drawn with bio-renders, can I put them in the paper or which other software I can use to draw them?

27 February 2021 8,179 1 View

Mediation path analysis - Can I run two seperate models?

I am wanting to run a serial mediation model with 2 x IVs, 2 x MVs, and 3 DPs (all continuous). Is it problematic to run 2 different models for each IV, keeping the MVs and DPs the same in each...

27 February 2021 5,681 3 View

Can anyone share his experience regards Smoothing in origin?

I am working on TiO2 composite material and the results of XRD have a lot of small/junk peaks and while I apply a smooth filter in Origin then the other characteristics peaks disappear so anyone...

26 February 2021 8,183 3 View

How to measure angle between laser travel path and machine axis in Laser Measurement system?

25 February 2021 1,987 3 View

Physical-chemical formation of stalactites/stalagmites. what promotes the formation/growth of these structures?

I know, or think I do, the basic idea behind these natural structures, as from what I know they form due to water dripping from the top leaving a salt deposit behind. But started to wonder about...

22 February 2021 1,400 4 View

Is there a suitable way to confine cell attachment area inside a multi-well plate?

Are there any types of cylindrical cell culture inserts that are designed to confine cell seeding area? Say, if I'm using a 12 well plate (3.5 cm^2/well), but only want to seed cells in the middle...

22 February 2021 7,127 4 View

How can a reference point be fixed to an attachment point in Abaqus?

I am currently trying to copy an assembly feature, that is present in an old version of the model I am using, onto a new model. The feature is a reference point that is fixed to an attachment...

16 February 2021 8,872 2 View

How to determine the significance of "diagonal" contrasts in two-way ANOVA interactions on SPSS?

Hi all, I'm running a 2 x 2 between-subjects ANOVA with the setup in the attached image (kindly refer to JPG attachment). I understand that calculating simple effects involves determining...

09 February 2021 547 3 View

Recommendations for sample size in visual qualitative research (using children's drawings)?

Hi everyone! Asking for a little help, if I may. I am working on a research project, where I aim to analyse children's drawings about Covid-19. I am fairly new to using visual data in qualitative...

07 February 2021 9,530 3 View

Best way to draw COLONY output / pedigrees?

Hi, I am using the sibship analysis software COLONY 2.0.6.6 (most recent version) on about 150 individuals offspring, with some of them as potential fathers and mothers. COLONY provides a lot...

02 February 2021 6,910 2 View