Under supercritical conditions the reforming of biomass into fuel gas takes place. Currently corrosion is observed by Cl and S.
Any steel pipe will be corroded at this conditions, mostly because of the moisture. You need protection coating.
Schiff base synthesis from cyclic ketone and primary amine
19 August 2023 5,579 4 View
I am conducting research in which I will be using a plant extract and infusing it into a wet wipe to fight the growth of bacteria and stop the spread of infections. I need to find a way to remove...
28 April 2023 2,206 2 View
research project on antibacterial activity of lavender essential oil , i have run into some issues with 96-well plate microdulition method for determining of minimum inhibitory concentration...
20 April 2023 3,696 0 View
I'm trying to understand how lupus (particularly SLE) develops due to immunodeficiencies. I've understood that it's a type 3 hypersensitivity (autoimmune disease), where immunocomplexes (of self...
21 November 2021 8,845 1 View
I have a permission from X company to use their graph from a report, but they have a reference in the bottom left corner of the graph as follows: "Source: Database Y". Is it OK to use this graph...
24 February 2021 2,670 3 View
Dear all, I want to investigate the velocity profile of water in CNTs(distribution of z component velocity along the radial direction and the radial component of velocity ). I divided the CNT...
06 February 2020 3,735 1 View
Dear users, I want to compute the viscosity of Tip3p model of water in CNTs. In some litratures said that about radial and axial viscosities, but others just said viscosity. I want to know that...
23 September 2019 372 1 View
Dear all, I want to know about the hydrodynamic equations for junction of pipes with non-uniform cross section. how about the Hagen-poisueille equation for these type of junctions? how could...
28 May 2019 3,842 5 View
Dear all, Does anybody simulate the hexagonally packed CNT with lammps? I want to study about water permeation through these membrane. please introduce me some papers. thanks
17 May 2019 2,839 5 View
Biostimulants / bio-effectors is now a multi-billion dollar industry but does it work on established plantation crops / trees like coffee? Some thougths: Diversity and composition of microbial...
07 January 2018 7,102 7 View
I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...
08 August 2024 719 0 View
I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...
07 August 2024 1,028 0 View
Suggest one of them 1. Teflon-lined stainless steel autoclave: 2. Alumina (Al2O3) ceramic container
30 July 2024 7,326 1 View
The catalytic effect of retained austenite refers to the phenomenon wherein quenching steels with a small amount of retained austenite, when subjected to tempering at a specific temperature...
27 July 2024 8,508 0 View
Please investigate the effect of temperature and strain rate of hot deformation and the formation of delta ferrite in martensitic stainless steel 410?
25 July 2024 9,408 0 View
I have tried to saturate ferritic steel with hydrogen using the electrolytic method and H2SO4. However, the effect was very poor even after 3 days of "saturation". Can anybody help in choosing a...
24 July 2024 4,393 2 View
I am simulating interlocking / dry stacked masonry in Abaqus. I am using a friction coefficient of 0.6 for my model as it is stated in the previous research as well as in the base paper. The...
16 July 2024 5,047 0 View
In the expression for solid solution strengthening model that has been widely used in the literature use a linear form consisting of strength coefficient, and concentration of elements in wt.%....
11 July 2024 4,476 3 View
Dear colleagues, I'm currently modelling a simple 4-point bending test of a concrete beam in Abaqus. However, the load-displacement curve was ascending (without final point), which didn't match...
29 June 2024 6,192 2 View
Dear colleagues, I'm researching some methods of measuring the moisture of iron pellets and iron concentrate in the steel industry (especially non-contact methods). If you have any information...
22 June 2024 7,894 2 View