13 July 2017 2 9K Report

I am modelling the wye branch in ANSYS and at the inlet I am giving the mass flow rate and outlet is set as pressure outlet.Do I need to add the pressure developed due to the height of the pipe from the intake or the velocity inlet is sufficient to model the system

More Manjil Puri's questions See All
Why uwb antenna group delay measurements taken at 30 cm?

UWB Antennas group delay measurements are carried by keeping antenna separated by 30 cm ftf or e2e configuration. The literature survey reveals it to be the abeyance of far-field condition.......

02 September 2020 6,404 3 View

Is research on antimicrobial peptides worth it?

In the age of Mutiresistant drug bacterium(s) and eukaryotic pathogenic organisms or superbugs, we are in a constant lookout for new treatments and especially antibiotic drugs. Two approaches, in...

23 August 2020 3,915 3 View

Is ATP the best energy providing molecule? can there be something better?

ATP energy-storing molecule as is no doubt an efficient! as not only it is used as energy storage and provider in all forms of life and has probably been around for billions of years. Even in the...

08 February 2020 9,015 6 View

How to know the concentration of compound in nanogram/Litre from a calibration graph in microgram/Litre?

I have calibration graph using GC-MS ion trap of a compound in microgram/Litres but i got the compound value in sample in nanograms/litre. Now i need to know the concentration of the compound. How...

01 February 2020 9,649 4 View

Solubility of paraffin wax(58-60) in organic solvents and non polar solvents?

Solubility of paraffin wax(58-60) in organic solvents and non polar solvents

18 March 2018 8,763 2 View

How to plot predicted probability of logistic regression with multiple variables?

I encountered a problem in plotting the predicted probability of multiple logistic regression over a single variables. For example, my model is Prob = - 0.727 + -0.002*X1+ -0.022*X2+ -0.002*X3+...

20 December 2017 5,725 11 View

Are wall panels having a width b lower than their height h are not considered to resist lateral loads. ???

Are wall panels having a width b lower than their height h are not considered to resist lateral loads. ???.

02 March 2016 1,389 3 View

What is the significance of the peak shifting of loss tangent towards lower temperature with an increase in frequency?

In my results, the peak of loss tangent shifts toward lower temperature when frequency increased while the peak of dielectric constant shifts toward higher temperature with an increase in...

12 December 2014 6,378 4 View

Where can I find theoretical raman resonant scattering cross sections in x-ray energy region?

I need to compare the measured cross sections for some heavy elements.

14 January 2014 133 2 View

What software is available for the analysis of qualitative data in social science research?

It becomes very difficult to analyse qualitative data. Quantitative data takes a lot less time to get results.

16 December 2012 2,597 37 View

Similar questions and discussions
MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

After a reference from Int J Body Compos Res, can any body help?

Hi, I am after the reference below, my library says it cannot obtain a copy either locally or internationally, any help appreciated! Chris Wang ZM, Heshka S, Wielopolski L, Pi-Sunyer FX, Pierson...

03 March 2021 6,193 1 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

What is the characteristic length to determine the Reynolds number for the scattered turbulent fluid flow?

Dear all, I just saw this example in FB on the difference between laminar flow and turbulent flow. The flow from a pipe hits the sink and scattered. The flow from the pipe is characterized as...

02 March 2021 1,999 5 View

Can we distinguish the type of free fluid inside the pelvic and abdominal cavities whether blood or serous fluid using the ultrasound?

during ultrasound examination of acute abdomen, sometimes we see free fluid , can we know the type of fluid ,whether blood or not , using ultrasound only? if yes , what are the sonographic...

01 March 2021 7,476 4 View

Our partners will collect data and use cookies for ad personalization and measurement. Learn how we and our ad partner Google, collect and use data. Agree & close