What may be the research scope or research gap for Electric Discharge Machining Process?

More Chintan Barelwala's questions See All

Which are the advanced objectives of parametric optimization of Wire cut EDM machining of the MMC AlSiC?

Is there any further objectives like fea of WEDM and other methodology used except optimization in Wire cut edm of AlSiC MMC material?

30 January 2023 5,971 3 View

How to categorise proteins based on the function?

Hi all, I wish to classify my proteins into the classes like the one in the attached image. I tried various bioinformatic tools including DAVID, panther, and gene ontology. However, they don't...

22 January 2023 7,101 2 View

Can I use HNO3 as solvent to make cerium oxide nano particles in sol-gel method? and the process I followed is sol-gel method or co precipitat method?

Cerium(III) nitrate hexahydrate [2 g, Ce(NO3)3·6H2O] was dissolved into 4.5M HNO3 (5 mL). Sodium hydroxide (10.50 g NaOH) was also dissolved into DI water (deionized water) (35 mL). This NaOH...

06 November 2022 8,602 3 View

What is the possible solution to the error "turbulence viscosity limited to viscosity ratio 1.000000e+05 in xxxxxx cells" in ANSYS Fluent?

Hello everyone, I am working with multi physics eulerian modelling in ANSYS. I am using k-epsilon model to work with simulation. Simulation is regarding stirring of molten Al in crucible or say...

28 April 2022 2,184 0 View

Why most of researcher used Wrought Al alloy to prepares Al MMC using stir casting process?

Wrought Al is already extruded grade then why most of researcher are not using Al cast grade And very few researchers worked on cast Al grade during stir casting. If one can given insight on why...

09 November 2021 2,138 4 View

Respiratory syncytial virus plaque assay?

Hello, I am trying to perform a respiratory syncytial virus (RSV) plaque assay. I can see the syncytial formation, white dots with a crystal violet background (3 replicates). However, I don't see...

18 October 2021 5,082 2 View

Which AlSiC compnent used in automobile, aerospace etc. manufactured by using Electric Discharge Machining Process ?

I have observed many papers in optimization of electric discharge machining on different MMC compositions. But, nowhere I found application of EDM for such parts. I want to know which AlSiC...

27 June 2021 3,290 1 View

How can we count the number of edges in an edge detected image using canny/sobel algorithm in MATLAB?

I need to process an image for edge detection and then want to count the number of edges in that image.

29 December 2020 5,961 2 View

Is there any workaround for MaxQuant when it crashes unexpectedly without giving any errors?

I am processing my MS results that were acquired in Orbitrap instrument and it seems that as soon as I start the analysis on MaxQuant, it crashes unexpectedly with any error reports. This has...

01 October 2020 8,132 6 View

How to use Fischer exact test for daily survival analysis? Can I do it in SPSS?

I want to compare survival difference daily using Fischer exact test? How do I do get using SPSS?

12 June 2020 7,348 3 View

How does grain and grain boundary affect the ceramic when studying its dielectric properties?

I am not able to get good literature and the physics behind how first these grains and grain boundaries arises out of no where when we make a pellet to study its dielectric properties and then how...

07 August 2024 5,177 3 View

Why is the molecule's orientation with an electric field affect polarizability?

Why is the molecule's orientation with an electric field affect polarizability? Electrons are diffuse enough to be independent with respect to orientation and effect of electric field on...

03 August 2024 7,843 1 View

Does continues partial charging/discharging do any harm to the BESS performance and degradation?

For a grid connected BESS (lets say 100 MW/200 MWh system, LFP battery), if we charge the BESS in such a way that whenever we can access power from the solar that will charge the BESS. Hence it...

01 August 2024 9,903 7 View

Ternary in Electrical Engineering?

Dear Research Community I would like to invite Elctrical Engineering specialists to solve problems related to Ternary Algebra or tripple sets I have an algorithm that places in relation three...

28 July 2024 5,771 2 View

Can a shoot-through event of a tri-state digital buffer cause momentary Hi-Z state?

// interested in the difference between floating events and short circuits.

22 July 2024 6,565 0 View

What is the mechanism of atmospheric pressure plasma Jet (APPJ)?

In general, the characteristic of electric current as a function of voltage in argon plasma jet using dielectric barrier discharge in atmospheric pressure, jet length will increase by the increase...

16 July 2024 9,316 1 View

Availability of laser assisted machining (turning) in India?

Sir, I want to work on the laser assisted machining (turning) of Nickel Based Super alloy. Please help in finding the laser assisted machining facility in India. Thanks and regards

02 July 2024 2,086 2 View

What are the marginal properties of a space ?

Let's assume medium-free radio transmission where we know the boundaries are the emitter and receiver. We have not yet, using math, formulated the marginal properties of emptiness that must be...

24 June 2024 7,038 4 View

Weight of the matter how change at the electric field types?

Regional directed electric field and full homogenic dispersed electric field

10 June 2024 10,163 11 View

How to address gradient discontinuities in CFD - Ansys Fluent?

Assuming I have three domains (three cubes e.g.) placed side by side, the electrical potential equation ( which I am specifying as a User Defined Scalar (UDS)) is solved in the left and right...

05 June 2024 4,153 0 View

H.-P. Schulze

Might have to clarify first of all, the technical prerequisites you have. The nest would be the question of technical relevant applications and the resulting issues.

Best Regards

Hans-Peter

Shivraj Narayan Yeole

Answer to the question lies in the literature itself. Papers you referred may help you in getting the answer.

Below is a very generic and universal observation @ EDM

"Everybody knows EDM is slow machining process and also the tool wear is high. You may come out with some mechanism that could change this."

For more advanced scope, refer to the current literature.

Chintan Barelwala

Shivraj Yeole Thank you ....you mean to say mechanism to improve MRR & TWR.