16 June 2016 1 6K Report

I have to work on ANGPTL4 expression in lung cancer by using Apoptome immunofluoresence microscope. I have no experience in IF and I have difficult in choosing primary and secondary antibodies which is most suitable for Apoptome. Could someone suggest me for suitable antibodies?

More Nan Cho Nwe Mon's questions See All
Signal phase shift after analytical calculation?

Suppose we have a signal as x(t) = exp(i(omega*t + phi)), after a simple calculation as y(t) = 1/x(t). We can clearly see that there is a phase shift of Pi=180deg. However, using directly...

20 October 2020 4,923 5 View

Is it necessary to use ethanol to drain off glutaraldehyde?

Hi everyone! I'm using glutaraldehyde as a spacer to cross-link a primary amino and an enzyme on plat glass. After the step of immerging the support in 2.5% glutaraldehyde solution, one protocol...

20 July 2020 3,702 2 View

ORCA4.2.0 GTOInt error?

when I run ORCA, I got an error as follows: ORCA finished by error termination in GTOInt Calling Command: mpiexec -np 4 D:\ORCA421\orca_gtoint_mpi.exe na20.int.tmp na20 [file...

08 May 2020 5,444 3 View

No title

As you can see in the picture, the salt is stuck to the crucible. Anyone has experience of melting salt at high temperature? Would stainless steel crucible be better?

04 March 2020 3,412 3 View

Cell numbers in powder increase again after decreasing?

I used the raw substrates for formulation of bacteria for biocontrol. During storage, cell numbers decreased continuously during the first two months. However, it increased again after 2 months?...

24 July 2019 1,054 3 View

Why should SVD get two equal singular values for a single mode?

Singular Value Decomposition (SVD) is an important method in the area of signal processing. I try to use SVD to calculate the MHD mode structure from experiment data. However, during the benchmark...

10 April 2019 6,118 4 View

How to derive the Boltzmann equation in plasma physics?

Boltzmann equation in plasma physics is a very fundamental equation in kinetic theory. What's the relation of the one in plasma physics and that in thermodynamics.

03 April 2019 4,925 8 View

How to justify Increase in activation energy by increasing GDC/SDC?

how can we just justify the increase in activation energy by increasing the GDC/SDC content in sofc cathode..... for reference please see this paper page 6/2165.... DOI...

03 March 2019 3,132 3 View

C.elegans plate: what is the reason for the agar concentration of 1.7%? Can I increase it?

I am doing lifespan assays for ~35 genes simultaneously in C. elegans on FUDR (inhibiting reproduction) plates to avoid re-picking the worms. I tried it once and got positive results, but a...

06 February 2019 728 4 View

How about the minimum quantity/concentration/volume that I should add into wells when Gel electrophoresis?

In DNA/RNA Gel electrophoresis, which is the key factor, total quantity, or concentration, or volume, that may influence the lightness of bands?

05 August 2018 9,377 8 View

Similar questions and discussions
MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

Why does blocking with my immunogenic peptide cause nuclear fluorescence in ICC?

Hi all, I am validating a polyclonal antibody raised against human ANT4, through WB and ICC. In most of my controls, the antibody shows very little off-target binding, but when I pre-incubate the...

03 March 2021 5,999 3 View

What kind of fluid could I use for a pitfall trap that also does not invalidate molecular testing?

Hi, I want to start testing pitfall trap to obtain ants samples, but I need to conduct molecular analysis on those insects. So, what kind of fluid can I use? Ethanol expires too early and I need...

03 March 2021 5,978 5 View

I need to image mesoporous silica nanoparticles that are in ~100 nm size and do high resolution TEM to look at mesopores. what grids should I use?

Need to image mesoporous silica nanoparticles using the TEM. Also, need high resolution TEM images to see the mesoporous structure. Kindly suggest what kind of grids to use. Thanks, Shatadru

02 March 2021 1,787 2 View

Have someone successfully used the ER alpha (Santa Cruz sc-8002) antibody in immunostaining ?

Santa Cruz now recommends this new antibody (F-10) but I can't find a publication using this reference. I'm working on human et non human primate hypothalamus and so far, it doesn't work. Is...

02 March 2021 10,003 2 View

Our partners will collect data and use cookies for ad personalization and measurement. Learn how we and our ad partner Google, collect and use data. Agree & close