What is the welding thickness between the plates of brazed plate heat exchanger?

02 February 2019 1 2K Report

What is the welding thickness between the plates of brazed plate heat exchanger? and how it is considered in numerical modeling in ANSYS FLUENT?

Ahmad Aboulkhail

Exactly where between the plates at the points of contact there are points of welding will remain the distance between the plates themselves and how to take effect in numerical analysis?@ibrahim Halil yılmaz

Badges
Science topic

More Ahmad Aboulkhail's questions See All

What are the possible ways to ensure the validity of the results of the numerical study in computational fluid mechanics?

I am doing a numerical study of a new model of a heat exchanger and there are no previous studies on the same geometry that the study was conducted on. Is there a way other than conducting...

01 February 2020 9,327 9 View

How to set the boundary condition for temperature in the case of modeling a counter-flow heat exchanger using periodic boundary conditions?

I am trying to take advantage of the periodic boundary conditions in ANSYS FLUENT program to model a small area of a heat exchanger with a counter-flow. In boundary conditions I can put the...

08 September 2019 7,194 3 View

How can I apply in ANSYS Fluent the periodic boundary conditions?

I am currently studying the analysis of flow in a plate heat exchanger with a new plate geometry ... My question: How can I in ANSYS Fluent to apply on unit cell (single plate and two fluids with...

10 November 2018 2,828 4 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How to fix errors in my heat transfer steel structure with reinforced concrete slab model Abaqus?

I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...

07 August 2024 1,028 0 View

Is changing the medium during the experiment overestimate the results?

I am experimenting with cancer and non-cancer cells in a 12-well plate for 4 days with a seeding density 1*10^4/well, however, I noticed that the control group growth rate slows down on D3. Should...

07 August 2024 2,283 2 View

How to normalize and take the significance of the MTT OD values with 3 replicates for the same cell-line?

Hi, I have a question about normalizing the MTT OD values for doing the statistical analysis. So, if we have 3 different plates and we call them 3 different replicates, so, first we would...

07 August 2024 8,106 4 View

Why does my protein refolded to beta sheet during thermal denaturation analysis?

Hi! So i attempted to understand a novel protein behavior towards heat application by analyzing its secondary structure change. I subjected the protein to a thermal denaturation analysis using...

06 August 2024 1,989 3 View

How to heat polymer for about 130° without oil bath ?

is there any other way to heat a polymer evenly other than oil bath if so what are those and how to use it

06 August 2024 947 1 View

Can you recommend a 96-well plate for minimal cell adherence to the wells during phagocytosis experiments?

I have been performing short phagocytosis experiments using 96-round bottom, tissue culture treated, well plates (Falcon, 353077). I culture the cells with the phagocytic cargo for 2-4hrs, wash...

04 August 2024 5,228 4 View

What should I do with parameters that are not relate to my simulation in MyLake model?

I want to Estimate surface heat fluxes using MyLake, but I don't have all the initial values in model parameters section and other sections,is there a way?

04 August 2024 1,537 1 View

PBMC infection with virus?

In my study, I intend to infect PBMCs with SARS-CoV-2. After that, I will analyze NK cells by flow cytometry to see if their phenotype changes or if they show degranulation. After the infection, I...

01 August 2024 4,403 4 View

Found this object in the cell culture - do you have any suggestions what it might be?

Dear researchers, Today, we found this object in one of the wells of a 96wp culture plate. The plate contained MEC-1 cells and GelTrex. I am quite curious what this is (because it's not cells). Do...

01 August 2024 2,250 2 View