How to use commands in ansys workbench?

I am trying to input the material data in ansys mechanical with the help of command i have.This experimental data only consists of stress strain value of concrete cubes.I dont know where this code...

02 August 2020 7,769 5 View

How small can a 915 MHz RFID antenna (for tag, not reader)be?

For example, the antenna in this paper is very small. Can it be even smaller (such as

27 July 2020 8,748 8 View

Is there any commercial mems stress sensor chip ?

I had found some literature that develops MEMS stress sensor (CMOS, N-MOS, P-MOS). However, I can't find commercial solutions for this type of sensor. Is there any replacement? (Stress...

21 May 2020 6,360 6 View

How to apply displacement boundary condition in ansys?

i have data of compression test conducted on concrete cube of 150*150*150 in form of failure loads. How to calculate the displacement to be applied as a boundary condition in ansys workbench if...

07 May 2020 8,149 4 View

Strange problem in rf to dc rectifier?

The circuit is a voltage doubler, the diodes are sms7630. The reverse breakdown voltage of sms7630 is 2V. In ADS simulation, the output voltage never exceeds 2V. However, in practice, I can get...

18 December 2019 4,034 4 View

How do I add a particular RF Switch to CST Simulation?

I have a particular RF Switch with me that I need to test on CST. Is there any way to import the data of that particular RF Switch (such as equivalent circuit and/or S parameters) and test my...

22 September 2019 5,063 1 View

Can anyone help me find target displacement of high rise structures with and without core and outriggers?

I went through FEMA-356 and FEMA-440 for target displacement and I cam across the formula as well but it wasn't helpful as i'm not able to understand it completely and I wasn't able to find all of...

19 September 2019 9,261 5 View

How to block the current but release it when the voltage reach certain value?

I am working on rf energy harvesting. Now, a problem occurs. Breifly describe the circuit. Antenna--Rectifying circuit--Storage capacitor-- DC-DC converter--Load. Now, it seems that the UVLO...

15 June 2019 3,093 11 View

How can I get the lysate from human/mouse red blood cells to do a western-blot ?

How can I get the lysate from human/mouse red blood cells (RBC) to do a western-blot ? My interest gene has been widely reported to express on RBC and not well established in other tissues. And...

25 March 2019 6,972 3 View

What type of sensor should be used to measure the intensity of electromagnetic radiation in the microwave region?

I need to measure the intensity, at each frequency, of microwave radiation having a specific bandwidth with a central peak at 183 GHz. What sensors can be used for this purpose?

05 March 2019 9,360 3 View

What is the production process of CaFe ferroalloys?

I looking for ferro calcium production process

03 March 2021 1,755 4 View

How do I increase the yield of my PCR product?

Hello, We would like to increase the yield of our PCR product. We are running a series of PCR reactions that is targeting ~1.1kb sequence. We begin each reaction with ~400pg of template DNA...

02 March 2021 4,029 3 View

Precipitate after adding laemmli buffer to protein solution containing Potassium Acetate?

Hi, I am running a size exclusion chromatography experiment with a buffer containing Potassium Acetate as a salt. I analyse these fractions through SDS-PAGE. After boiling my SEC fractions in...

01 March 2021 2,622 3 View

1 nm thick MgO thin-film to be deposited on Si wafer using thermal evaporation. What will be the optimum deposition conditions?

Favourable conditions of base pressure, rate of deposition. Also, by which characterisation technique to be used to verify the thickness of the deposited film.

28 February 2021 3,640 3 View

How to delaminate copper in water-based anodes?

Hello everyone, I'm looking for a way to delaminate copper current collector of water-based anodes in Li-ion batteries without damaging the graphite film. I tried different materials such as HNO3...

24 February 2021 3,785 3 View

What is the best etching method for Mg-Ca alloy?

I have used Picral etchant (4.2 g Picric acid, 10 mL Acetic acid, 70 mL Ethanol, 10 mL distilled water) but it didn't work. Is there any alternative?

21 February 2021 2,558 5 View

How to prepare electrolyte of NaClO4 salt for Na-ion battery? Any problem with this salt?

Hello, I am trying to make anode for Na-ion batteries. I have no experience with preparation of the electrolyte for any batteries. NaClO4 salt are available and I am planning to use EC:PC as...

21 February 2021 8,132 1 View

I want to remove TiO2 and SiO2 coating from surface. any one can help me?

I want to remove TiO2 and SiO2 coating from surface. I think that i should use HCl and MgCl2 and an oxidation agent such as potassium nitrate, but i dont know in which propertion should these...

14 February 2021 300 3 View

Does any one have experience with Autoclavable cell culture media (RPMI 1640/DMEM)? Does it work well?

12 February 2021 2,958 1 View

How to determinate of molecular structure of salt into the liquid?

I need to determine the open formula of our complex, presumably consisting of sodium tungstate Na2WO4 and aluminum sulfate Al2 (SO4) 3. Our problem is that with an increase in the concentration...

11 February 2021 5,821 1 View