22 January 2016 1 6K Report

I am getting the error in the Femwater model while giving the input data of the well. It shows refine point is to close to the boundary or another refine point. The point was ignored.

More Konstantin J Sylus's questions See All
Formation of a target organizational and functional model for data management in space activities?

Formation of a target organizational and functional model for data management in space activities

10 July 2024 4,498 0 View

What connection can there be between politics and collective intelligence?

I am interested in reflecting on the political dimension of collective intelligence.

13 April 2024 2,811 18 View

How can the concentration of colloidal particles in an aqueous solution be determined?

How can the concentration of colloidal particles in an aqueous solution be determined? Is it possible to apply the photo-colorimetric method for this?

11 October 2023 1,563 21 View

What's a detailed chapter one of a research project in mechanical engineering?

what's a detailed chapter one of a research project in mechanical engineering? especially for undergraduates

27 September 2023 4,955 0 View

In the design analysis of a honey making machine from honey combs through squeezing, what could be the material properties?

What could be the design considerations that an engineer need to take into account?

29 May 2023 1,364 1 View

Where can I find data about viscosity dependence on concentration in methanol–poly(vinyl acetate) solution?

Where can I find data about viscosity dependence on concentration in methanol–poly(vinyl acetate) solution? What value of saturation concentration and diffusion coefficient for the solved polymer...

11 April 2023 3,414 2 View

Is there the state support for medical insurance of radioisotope diagnostics in your country?

Radioisotope diagnostics of many diseases is currently available in many countries. But this is often an expensive procedure. Does your country provide state support for medical insurance for...

01 April 2023 3,895 7 View

I'm looking for a good review article/book chapter about parrallel methods based on simulated annealing. Any recommendations?

I am currently studying the application of simulated annealing techniques to optimization problems. In particular, I am interested in applying the optimization method to the study of Ising models....

21 November 2022 2,663 1 View

Amplification in regenerative amplifier by cw pumping?

Hello. In real moment I'm designing the CPA system for my Ti:Sa laser. I have only cw diode module for pumping (10 W). How can I evaluate amplification opportunity in 'regen'. I want to gain from...

18 September 2022 5,450 1 View

Why is there increase of electrode atomic forces when applying bias voltage in TranSiesta?

Dear colleagues, I am trying to calculate I-V characteristics for typical (Left electrode) - (Device) – (Right electrode) system. Besides the well-known problem of difficult electronic...

27 March 2022 8,532 11 View

Similar questions and discussions
How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

What are the shear and normal stiffness values of an LLDPE liner in 3D numerical modeling of a stockpile?

I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...

05 August 2024 3,665 0 View

Is it necessary to covary exogenous constructs in a structural model?

I am working on a SEM model where i have 7 latent variables (6 exogenous and 1 endogenous). In AMOS when I co-vary the exogenous constructs, only 2 paths are coming significant out of 6. But when...

03 August 2024 6,028 4 View

Given the current level of natural phenomena cause by the climate change and environmental pollution, will the AI find the technological solutions?

AI-driven technologies offer previously unheard-of capabilities to process enormous volumes of data, extract insightful knowledge and improve predictive models, according to the UN’s World...

31 July 2024 9,733 3 View

Our partners will collect data and use cookies for ad personalization and measurement. Learn how we and our ad partner Google, collect and use data. Agree & close