19 September 2022 1 6K Report

Hello. In real moment I'm designing the CPA system for my Ti:Sa laser. I have only cw diode module for pumping (10 W). How can I evaluate amplification opportunity in 'regen'. I want to gain from 1 nJ to 150 mkJ.

More Konstantin Emelianov's questions See All
Formation of a target organizational and functional model for data management in space activities?

Formation of a target organizational and functional model for data management in space activities

10 July 2024 4,498 0 View

What connection can there be between politics and collective intelligence?

I am interested in reflecting on the political dimension of collective intelligence.

13 April 2024 2,811 18 View

How can the concentration of colloidal particles in an aqueous solution be determined?

How can the concentration of colloidal particles in an aqueous solution be determined? Is it possible to apply the photo-colorimetric method for this?

11 October 2023 1,563 21 View

Where can I find data about viscosity dependence on concentration in methanol–poly(vinyl acetate) solution?

Where can I find data about viscosity dependence on concentration in methanol–poly(vinyl acetate) solution? What value of saturation concentration and diffusion coefficient for the solved polymer...

11 April 2023 3,414 2 View

Is there the state support for medical insurance of radioisotope diagnostics in your country?

Radioisotope diagnostics of many diseases is currently available in many countries. But this is often an expensive procedure. Does your country provide state support for medical insurance for...

01 April 2023 3,895 7 View

I'm looking for a good review article/book chapter about parrallel methods based on simulated annealing. Any recommendations?

I am currently studying the application of simulated annealing techniques to optimization problems. In particular, I am interested in applying the optimization method to the study of Ising models....

21 November 2022 2,663 1 View

Why is there increase of electrode atomic forces when applying bias voltage in TranSiesta?

Dear colleagues, I am trying to calculate I-V characteristics for typical (Left electrode) - (Device) – (Right electrode) system. Besides the well-known problem of difficult electronic...

27 March 2022 8,532 11 View

How to block an IR beam in vacuum?

Hallo, I've a HHG setup, but the IR filter is broken. This means that the entire IR intensity hits the CCD camera and would destroy it. Because a replacement filter needs a few weeks to arrive,...

27 February 2022 5,470 1 View

How to determine the fraction of DNA from lymphocytes in the blood?

I'm thinking about how to detect in circulating free DNA fraction that comes from white blood cells. Now my idea is to use T cell receptor excision circle (TREC) and kappa-deleting recombination...

01 June 2021 5,918 0 View

I need cybersecurity datasets for training machine learning algorithms, where I can find ?

I need cybersecurity datasets for training machine learning algorithms, they could be for: - intrusion detection - DDoS detection - Malware detection - etc.

28 May 2021 5,982 6 View

Similar questions and discussions
Using OBD technique i am trying to measure laser induced shockwaves velocity i found that at start velocity increases and then decay?

i am unable to interpret why its increases in start as shown in figure

11 August 2024 2,179 1 View

Hello researchers Is this a random laser or just fluorescence?

I am using Rhodamine6G as gain medium and silver nanoparticles as scatterers on a microscope slide and laser input 532 nm comes from above.

09 August 2024 9,894 2 View

Could dyes amplify the spectrum of light to a specific wavelength?

I am interested to know the behavior of dyes toward light. Specifically, Blue dyes re-emit the spectrum, especially from the green zone (known as principal in LED lamps, and blue dyes are known...

05 August 2024 3,290 1 View

How should operational parameters be selected when developing a pore-free laser welding technology?

There are three operating parameters - the laser power, the diameter of the focus spot and the scanning speed. It is necessary to obtain a seam of a given depth without pores. What parameter...

27 July 2024 7,168 2 View

Can we fit a gaussian Fit on a LIBS Peak ?

Though much literature suggests fitting a Voigt profile on a LIBS peak, is it also possible to fit a Gaussian profile on the LIBS peak? I have 204 spectra files, and I am building a pipeline for...

23 July 2024 6,127 1 View

Could someone please provide a list of journals that accept the application of methodologies in nature-based solutions?

I am looking for journals that admit the publication of results from applying the IUCN Standard for designing and monitoring Nature-based solutions. Many thanks for considering my request.

23 July 2024 6,444 2 View

How to download free version of BiofilmQ ?

I would like to use biofilmQ to analyse confocal laser image, how can do?

16 July 2024 7,628 2 View

When Using SYBR Green for Flourescent Detection of LAMP Products what causes an Overshoot in Flourescence Reading?

The Graph below shows an example of an amplification curve that shows an overshoot in fluorescence. I am using SYBR Green, BST polymerase, and 6 LAMP primers in the mixture and amplifying at 65...

14 July 2024 1,483 0 View

How to install Quantum Espresso with Intel compiler ?

Hello ! I would like to do band structure calculations of perovsikites materials with quantum espresso. For this I installed the Intel Fortran compiler. This is what I get when I run the...

08 July 2024 1,207 0 View

How to add a mass source term in the continuity equation?

Hi, I am trying to model laser cladding in Ansys FLUENT. There are two phase: one is base metal surrounded by an inert gas (shown in the image). I want to add a cladding layer of the same metal....

07 July 2024 1,182 8 View

Our partners will collect data and use cookies for ad personalization and measurement. Learn how we and our ad partner Google, collect and use data. Agree & close