How can I know the rank of each node in RPL in NetSim after simulation?

I am able to successfully run IOT RPL simulations in NetSim but in the results window, animator and plots I am not able to find the rank of the nodes. Please let me know how can I find this. Thanks

03 August 2020 3,630 3 View

How to do web scraping of VirusTotal so that I can get the information of multiple APKs?

VirusTotal website is a tool for detecting malware Android apps. But it also gives various information related to the APK uploaded, like manifest tags, permissions etc. I want to extract these...

07 April 2020 7,228 2 View

Based on the figure deduce the total no. of polypeptide chains in the protein?

A purified oligomeric protein was analysed by SDS - Page under reducing and non reducing conditions. A 1 litre solution of 1mg/ml concentration has 4.01*10^18 molecules of the oligomeric protein....

15 November 2019 5,362 3 View

What is the value of M/Z at base peak of benzoic acid/?

The mass spectrum of benzoic acid will generate the fragment as a base peak (100% relative abundance) of m/z (mass to charge ratio) at?

08 November 2019 1,175 3 View

How to find molecular weight of a protein through mass spectrometry?

An uncharged protein (P) has an Asp in position 23 with a molecular weight of 6501 Da, as determined by mass spectrometry. The uncharged mutant of this protein (P') contains a single amino acid...

06 November 2019 9,961 3 View

How to detect pilocarpine(quantitatively) in a mix of acacia gum and Na-CMC ?

I am looking for a method to detect quantitatively, pilocarpine hydrochloride(drug) in a mixture of sodium carboxymethyl cellulose and acacia gum. While using UV Spectroscopy, acacia gum sticks to...

25 December 2017 6,783 1 View

Protein is not entering into gel (8%) from wells after DSS cross-linking?

23 September 2017 4,518 6 View

How can I convert a 2D array 1632x11 to a 3D array 32x11x51 in Matlab?

24 July 2015 4,061 3 View

What are the mechanical properties of human cortex tissue?

Suggestions needed regarding some previous works done in the field of measuring mechanical properties of human brain cortex tissue. Also the response to stress, strain, compression force that any...

22 February 2014 4,316 2 View

Accuracy in EEG Data?

I am working on a project where I am trying to control the mouse cursor movement (up,down,left,right) using EEG data, I got from community sdk which is average band powers. I have used KNN and...

01 January 1970 7,491 2 View

Why can't make aluminum nitride film successfully by use sputter?

We use reactive sputtering process to make aluminum nitride film, and want to make c-axis aluminum nitride film on a silicon substrate, but the crystal orientation cannot be seen with...

03 March 2021 7,975 3 View

What thickness need for ITO to use as conductive layer?

I want to do RF sputtering of ITO on glass substrate using magnetron sputtering. what thickness do i need to make it good conductive layer to use it for PSC. Moreover, whats about thickness of...

01 March 2021 395 3 View

Glass fiber content in a gypsum board ?

Any idea on how to get the volumic ratio of glass fiber in a gypsum board ? Thank you for your help !

01 March 2021 2,501 3 View

How to check the uv-vis absorption of nanoparticle by surface plasmon resonance?

I try to check the uv-vis absorption of Indium nanoparticle. Now I am measuring in solution, can I measure it in the form of a film?

01 March 2021 930 3 View

1 nm thick MgO thin-film to be deposited on Si wafer using thermal evaporation. What will be the optimum deposition conditions?

Favourable conditions of base pressure, rate of deposition. Also, by which characterisation technique to be used to verify the thickness of the deposited film.

28 February 2021 3,640 3 View

Concrete compressive strength databases?

I am looking for datasets similar to this one: http://archive.ics.uci.edu/ml/datasets/Concrete+Compressive+Strength I am looking for concretes with different types of aggregates (Recycled,...

27 February 2021 6,801 3 View

How to prepare a thin polymer film by post-polymerization/crosslinking?

24 February 2021 2,362 5 View

How to properly calculate the fluid solid heat transfer between polypropylene matrix and glass fiber in a porous medium?

I'm building a cfx model of thermoplastic pultrusion process on ansys and i have a doubt on how is the proper way to set this parameter in a porous medium

24 February 2021 1,915 1 View

How to delaminate copper in water-based anodes?

Hello everyone, I'm looking for a way to delaminate copper current collector of water-based anodes in Li-ion batteries without damaging the graphite film. I tried different materials such as HNO3...

24 February 2021 3,785 3 View

How to determine solutionizing time for cast Al alloys?

For wrought alloys soaking time at solutionizing temperature is determined by thickness .Do we have such standards for cast Al alloys

23 February 2021 8,839 3 View