Usually the ride comfort is evaluated in terms of rms acceleration at seat level. Our (my) experience is that, the ride is more uncomfortable due to jerk than acceleration.
Is there any work on the effect of jerk on ride comfort ?
Dear Sir,
pl check it.
http://link.springer.com/article/10.1007/s40864-015-0012-y
For European values, the requirements are in EN 13803
What are the different national recommendations for UHPFRC concrete, which covers the flexure and shear design equations?
24 December 2021 1,094 2 View
As a part of my PhD thesis, I am developing a UHFRC concrete mix based on locally available materials. After a few trials, I got 7-day compressive strength of concrete around 82 MPa. In the same...
11 December 2021 5,782 9 View
After alkaline treatment (various % concentrations) with Natural fiber, dry in the hot air oven at 70 degrees Celcius for 4hrs. 1). 'Na' is coated on the surface of the fiber. how a coating of...
22 September 2021 1,275 5 View
I conducted Mann-Whitney test in JASP. The test results produce following data: U (or W) value: 15641.5 df= 2 p value = 0.001 Hodges-Lehmann Estimate: 5.527e -5 Rank-Biserial Correlation:...
16 August 2021 3,894 4 View
Raw sugar is generally golden brown-honey colored. The raw sugar is converted into white sugar using the refinery process, in which the raw sugar solution (melt) is treated with phosphoric acid...
20 May 2021 1,108 3 View
Recently I, got opportunity to oral presentation of my research paper in "international conference", abstract of which is published in private circulation of that publisher. Can I send the full...
04 March 2021 5,903 12 View
Consider a mass (m) suspended by a spring (k) and undergoes a static deflection X. 1. Force equilibrium method: k*X = m*g , gives X = m*g/k 2. Energy method: According to work energy principle,...
15 April 2020 5,839 0 View
Ayurvedic herbo-mineral formulations are very complex in nature. Even their methodof preparations is also very complex. So in such cases the modern advanced analytical tests are employed to...
29 December 2019 3,456 3 View
Is there anyone tested potential of PRISMA (PRecursore IperSpettrale della Missione Applicativa) i hyperspectral data for varietal discrimination?
24 June 2019 8,113 2 View
I am looking for more information about numerical damping.
24 July 2018 6,605 8 View
I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?
11 August 2024 3,115 1 View
I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...
10 August 2024 4,005 2 View
Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...
09 August 2024 7,892 0 View
I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...
09 August 2024 5,048 2 View
I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...
08 August 2024 719 0 View
Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...
06 August 2024 9,986 2 View
I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...
05 August 2024 454 3 View
I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...
05 August 2024 3,665 0 View
I am working on a SEM model where i have 7 latent variables (6 exogenous and 1 endogenous). In AMOS when I co-vary the exogenous constructs, only 2 paths are coming significant out of 6. But when...
03 August 2024 6,028 4 View
Regarding a model for simulating battery charge and discharge, what do you consider to be high fidelity? What is the acceptable percentage of error (regardless of the metric)? Could you suggest...
03 August 2024 5,358 0 View