What is the loss factor for fibreglass?

14 July 2020 1 5K Report

A thin composite plate which is made of fibreglass should have a loss factor around 0.05. But you will never know the actual value unless you test it in the laboratory.

Does anyone measured the loss factor of fibreglass plates?

Murat Kara

Dear Aygün,

You may examine the following papers for the loss factors of laminated thin fibreglass composite plates.

Article A modal impedance technique for mid and high frequency analy...

Article Determinations of in-situ energy loss factors of point-conne...

Best regards...

Badges
Science topic

More Haydar Aygun's questions See All

Is there any mechanism between Methyl dihydrojasmonate and secondary metabolite production?

Is there any mechanism or relationship between Methyl dihydrojasmonate and secondary metabolite production? Especially when it comes to medicinal plants that members of Asteraceae family.

02 December 2020 704 4 View

The effect of molecular weight on the glass transition ?

as i understand by increase the molecular weight of the polymer ,glass transition ( Tg ) increases but why some polymer have high molecular weight but it is glass transition is lower than...

20 July 2020 7,484 7 View

What would be the formula for calculation of Threshold consumption rate due to ingestion of medicinal plant?

In a article published in science direct entitled as "Preliminary investigation of naturally occurring radionuclides in some traditional medicinal plants used in Nigeria", the author used the...

09 February 2020 4,059 0 View

Is it required to concentrate sea water sample prior to gamma spectrometry analysis??

Suppose we have 10 L of sea water sample and we want to determine the activity of gamma emitting radionuclides in it. Is it required to concentrate this sample prior to gamma spectrometry analysis...

08 October 2019 5,454 3 View

What is Coincidence summing in gamma spectrometry and When it is required to make a correction for it?

During the interference Correction of the 226Ra 186.2 keV line by the 235U 185.7 keV some authors (F. De Corte et al, 2005) use the formula as given in attachment: Where, Ig, is the gamma-ray...

24 September 2019 2,755 2 View

How to Calculate Net count rate uncertainty in gamma spectrometry Technique?

We have a shrimp sample from IAEA for proficiency test and as per the requirement of IAEA we want to identify and quantify radioactivity in that sample. We have taken a sample count for 90000...

21 September 2019 6,649 14 View

How to Correct the interference of the 226Ra 186.2 keV line by the 235U 185.7 keV line?

Methods for the determination of radium isotopes in environmental solids by gamma spectrometry can be obtained by two means, the direct measurement of the principal photopeaks (186 keV in the case...

28 August 2019 9,267 10 View

How to handle imbalanced data in classification ?

I have a labeled data set which have 4 classes and there class distribution is given below -- First Class ( 70% ) Second Class ( 22% ) Third Class ( 3% ) Fourth Class ( 3% ) in this data set i...

15 October 2016 7,355 7 View

What does 'divergence detected in AMG solver: x-momentum' mean and how can I solve this problem?

I am investigating the wave propagation in a tube with a Helmholtz resonator attached to one end by using CFD. I am using a temperature profile and an UDF unsteady solver. each time I run...

27 July 2014 5,858 5 View

Whats the best software to process Genetic Algorithm?

need you advice guys, I want to make a research about GA, but I still considering about whats the best software that I must use to process my data. please give me your reason why. thanks in advance.

01 November 2011 261 20 View

Is changing the medium during the experiment overestimate the results?

I am experimenting with cancer and non-cancer cells in a 12-well plate for 4 days with a seeding density 1*10^4/well, however, I noticed that the control group growth rate slows down on D3. Should...

07 August 2024 2,283 2 View

How to normalize and take the significance of the MTT OD values with 3 replicates for the same cell-line?

Hi, I have a question about normalizing the MTT OD values for doing the statistical analysis. So, if we have 3 different plates and we call them 3 different replicates, so, first we would...

07 August 2024 8,106 4 View

Can you recommend a 96-well plate for minimal cell adherence to the wells during phagocytosis experiments?

I have been performing short phagocytosis experiments using 96-round bottom, tissue culture treated, well plates (Falcon, 353077). I culture the cells with the phagocytic cargo for 2-4hrs, wash...

04 August 2024 5,228 4 View

PBMC infection with virus?

In my study, I intend to infect PBMCs with SARS-CoV-2. After that, I will analyze NK cells by flow cytometry to see if their phenotype changes or if they show degranulation. After the infection, I...

01 August 2024 4,403 4 View

Found this object in the cell culture - do you have any suggestions what it might be?

Dear researchers, Today, we found this object in one of the wells of a 96wp culture plate. The plate contained MEC-1 cells and GelTrex. I am quite curious what this is (because it's not cells). Do...

01 August 2024 2,250 2 View

Publishing a checklist?

Does anybody know of entomological Journals without page charges that would publish an extensive checklist (Hong Kong Aculeates wasps) covering 350 species (of which more than half are new to Hong...

01 August 2024 6,134 2 View

HEC 1A & HEC1B Cell Lines?

Hi, Kindly guide me that how many cells of HEC1A & HEC1B Cell lines should I seed for Wound healing assay and which plate type is recommended 6, 12 & 24?. Articles suggested mainly 24...

20 July 2024 4,143 2 View

Masonry Interaction Module ABAQUS?

I am simulating interlocking / dry stacked masonry in Abaqus. I am using a friction coefficient of 0.6 for my model as it is stated in the previous research as well as in the base paper. The...

16 July 2024 5,047 0 View

How can we simulate(with FEM) the shape of Mobius strip using Abaqus Learning edition?

Aim is to simulate the shape of Mobius strip (an elastic ribbon) in simple way ( using Abaqus Learning edition). In literature, Mobius strip is modeled as Kirchhoff Rod / Cosserat plate. But, such...

15 July 2024 4,388 1 View

How to calculate CFU/m3 in settle plate?

14 July 2024 1,816 1 View