What is the incubation period, temperature and buffer recipe for LexA proteolysis by RecA?

02 September 2022 0 497 Report

Please let me know about the incubation period and temperature for proteolysis for lesA by RecA.

Badges
Science topic

More Charli Kaushal's questions See All

How to perform quantitative percentage analysis of minerals in XRD analysis..?

I am trying to perform the quantitative analysis of minerals in my samples. I have the XRD raw data of my samples. I started Rietveld refinement in X'pert Highscore and Match!* software but there...

22 April 2024 9,318 5 View

Lab 6 filament life in JEOL TEM?

How to check LAB6 filament running hours in JEOL 120KV 1400. When we can say that the filament has blown off?

02 November 2023 402 1 View

How can we do quantitative analysis of XPS peaks..?

How can we perform a quantitative analysis of the XPS peaks using Origin software? Please help, How can we do a quantitative analysis of each peak? The peaks of C1s are attached below.

31 October 2023 5,330 4 View

Please help, how can i calculate the quantitation peak (mole%) percentage of XPS Data..?

Can anyone please help me with how I can get the quantitative (mol%) value of any sub-peaks that are part of the main peak, such as N, C, and O?

26 October 2023 6,307 6 View

How can i exclude reference during similarity check on iThenticate..?

While conducting the similarity check, I have already excluded the bibliography and quotes. However, references after sentences are still appearing in the similarity check. How can I exclude...

25 August 2023 7,240 0 View

Asked question related to thermal kinetics of DSC scan?

Recently, we conducted DSC experiments on various glassy alloys within the SeTeSnIn system. I have provided the attached DSC scans for your examination. Similar DSC scans were obtained at...

20 July 2023 2,099 3 View

What value should i fill in search peaks section in X'pert High-score software for mineral peak analysis..?

I have X'pert high-score software for XRD analysis with PDF2 Database, please help me regarding search peaks section.

16 June 2023 6,447 6 View

Can we write running coupling constant of QCD as a function of interquark separation distance ?

Running coupling constant is always written as a function of momentum. Is it possible to write in terms of interquark separation distance? If so, what will be the formula?

13 June 2023 7,594 0 View

I am getting pure number as eigenvectors after solving Schrodinger equation using Numerov method in mathematica ? How to get wavefuction at origin ?

In mathematica, after I solve Schrodinger equation using Matrix Numerov method, I am getting pure numbers as eigenvectors. Is it possible to get pure numbers as eigenvectors? Now if I want the...

15 May 2023 8,075 0 View

Does anyone know about the original literature regarding Vitrinite Reflectance (Ro) % equation?

Please provide me original literature or reference material for the given equation. Vitrinite Reflectance (Ro) % = -2.712 * log(V.M.) + 5.092 Where V.M. is on a dry ash-free basis.

27 April 2023 6,482 6 View

AMAXA Lonza nucleofection lower volume of buffer?

Does anyone tried to do nucleofection with AMAXA by Lonza with lower than recommended amount of buffer in the cuvettes (100 ul)?

07 August 2024 4,616 0 View

Why I can't see any band in SDS-PAGE?

Currently, when I run SDS-PAGE, I don't see any bands at all, even though I used the same material just a day ago and it worked fine.... In our lab, we dilute the 10X running buffer to 1X and...

06 August 2024 5,373 2 View

Why might the impedance values for DI water and 0.1X PBS buffer solution exhibit a decreasing and increasing trend, respectively over time (HP 4194A)?

Hello everyone, I'm encountering an issue with my electrochemical impedance spectroscopy (EIS) measurements and would appreciate some insights. Experimental Setup: Electrodes: Gold interdigitated...

05 August 2024 3,783 2 View

What is the best blank for nanodrop if I want to read a recombinant protein concentration?

Is it the "elution buffer" or the "dialysis buffer"? Note: I'll be using NanoDrop OneC

01 August 2024 967 3 View

EDTA buffer solution?

Hello everyone! How can i prepare EDTA buffer solution (pH 8.2) to determine GSH levels? Thank you in advance.

29 July 2024 4,374 1 View

Whether i can preserve leaves samples in 2.5% glutaraldehyde in 0.05 M phosphate buffer, pH 7 for coming several weeks for further LM study ?

I want to preserve the sample leaves for the LM study of the stomata and conidia analysis. Whether 2.5% glutaraldehyde in 0.05 M phosphate buffer with pH 7 can be applied for preservation.

29 July 2024 8,560 0 View

Can a shoot-through event of a tri-state digital buffer cause momentary Hi-Z state?

// interested in the difference between floating events and short circuits.

22 July 2024 6,565 0 View

How can EDTA be removed from already extracted DNA samples?

Our lab has extracted bacterial DNA samples using Qiagen DNeasy kit and eluted the samples in AE buffer. However, this buffer contains 0.5mM EDTA not suitable for downstream application. Any ideas...

13 July 2024 1,675 3 View

How much 1X TAE buffer should I use in preparing 1.2% agarose gel?

Commonly, we prepare 1.0% of agarose gel with 0.4g agarose powder and 40ml 1X TAE buffer. if I would like to prepare a 1.2%% of agarose gel, is it I need to add 0.48g agarose powder and 120ml 1X...

12 July 2024 2,058 5 View

My Cyclic voltammetry curve doesn't show cathodic peak of Cu2+ to Cu+. how to solve this problem?

I performed CV of Cu-MOF in a buffer solution of pH 8, and we did not find any peak corresponding to Cu2+ to Cu+. What is the reason behind this? Please give your valuable suggestions.

08 July 2024 2,388 4 View