How does two neighbor D2D devices measure the signal strength and SINR or SNR from the neighbors?
RSSI is the signal strength that is measured by mobile devices in the download link of LTE transmission. RSRP is the reference signal received power as measure by the eNB during UL transmission
In a few papers, I have read the Asymptotic analysis of Signal-to-Interference-Plus-Noise (SINR) coverage probability. But I cannot actually understand the difference between the conventional...
05 June 2019 7,984 3 View
I am looking after how specifically LTE/LTE-A resource allocation takes place at eNB of current cellular architecture? The answers I am looking for are 1. How many RB are allocated for each users...
02 March 2017 9,164 4 View
What does LINK mean in the link level simulation? What are the differences between the two simulation methods?
11 December 2016 10,283 3 View
Please where can I get a pathloss and channel model for mobile femtocell covering all aspects of mobility within femtocells?
10 November 2016 10,061 3 View
5G cellular research is proposing several new aspects in terms of radio access technology, cell sizes, Antenna technology etc. But I think the major hurdle in implementing a less than ms latency...
10 November 2016 4,586 1 View
If X = x +iy; where x, y are Independent and Normally distributed variables. Then X is the rayleigh distributed signal. For a Rayleigh distributed channel, does abs(X)^2 represent the power of...
09 October 2016 2,243 6 View
I am working on D2D communication and need to design power control algorithm for minimum SINR values typical for a UE? Can I get general minimum SINR (or SNR values in one of my case) that can...
08 September 2016 8,120 5 View
Hey all. The rate of mobile user activity has been considered as exponential distribution in much of the literature. How is that? Following are my own understanding. Mobile users' (read cellular...
07 August 2016 723 4 View
Since D2D will find its application in out-of-coverage scenarios especially for public safety applications, devices needed to get synchronized first to power-efficiently discovery devices. What...
01 January 1970 5,383 1 View
How can I determine a good adhesion strength range for coatings on polymer surfaces, such as DLC on polymer substrates? Is there a specific threshold for adhesion strength (from T-peel tests)...
10 August 2024 942 3 View
Air moisture harvesting Air water collection devices
06 August 2024 5,473 2 View
Dear all, I am working on analyzing data from a survey on student satisfaction. The survey contains items with a 7-point Likert response format that produce 12 scales related to different areas...
05 August 2024 2,141 4 View
Hi everyone, If you have written or come across any papers where Generalised Linear Mixed Models are used to examine intervention (e.g., in mental health) efficacy, could you please share the...
04 August 2024 4,130 4 View
Hello. I am working on ROS production of two systems: system A is cerium oxide and hydrogen peroxide, system B is cerium oxide nanoparticle, hydrogen peroxide and potassium bromide. I did some...
04 August 2024 5,974 3 View
How do you tie-break and rank these two in their strength?
03 August 2024 4,471 1 View
Machine learning (ML) has shown great potential in predicting the compressive strength of concrete, an important property for structural engineering. However, its practical application comes with...
03 August 2024 2,546 2 View
Only Journals make money from the articles we have worked on for years. Academics do not earn money from their refereeing. Then shouldn't the solution be a system in which academics can earn...
01 August 2024 6,469 6 View
What types of mask designs for metal deposition, to be used in a PVD system, are best suited for perovskite-based solar cells?
31 July 2024 4,835 3 View
Dear researchers, Why specific capacitance is not proportional to the specific surface area? I have material A with a surface area higher than material B, but material B is showing little bit...
26 July 2024 9,156 2 View