What does it mean by Asymptotic analysis of a cellular Network?

In a few papers, I have read the Asymptotic analysis of Signal-to-Interference-Plus-Noise (SINR) coverage probability. But I cannot actually understand the difference between the conventional...

05 June 2019 7,877 3 View

How specifically resource allocation takes place in LTE/LTE-A system?

02 March 2017 9,004 4 View

What is the difference between Link level and System level simulation in communication?

11 December 2016 9,999 3 View

Pathloss model for mobile femtocells?

10 November 2016 9,941 3 View

Are the backbone / core network hurdle in implementing Novel ideas in 5G communication?

5G cellular research is proposing several new aspects in terms of radio access technology, cell sizes, Antenna technology etc. But I think the major hurdle in implementing a less than ms latency...

10 November 2016 4,463 1 View

How to calculate Power of Rayleigh Channel / Rayleigh distributed signal (multipath effect)?

09 October 2016 2,118 6 View

What is the minimum SNR values for OFDMA LTE-A UE receiver?

08 September 2016 7,966 5 View

What is the best method for predicting rate of cellular users' activity ?

Hey all. The rate of mobile user activity has been considered as exponential distribution in much of the literature. How is that? Following are my own understanding. Mobile users' (read cellular...

07 August 2016 575 4 View

What is the difference between RSSI and RSRP? Which signal strength measure will be used in between neighbors in D2D? Any research article?

01 January 1970 9,171 1 View

error in running a model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

error in modelling model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

MGL tools

20 June 2021 0 0 View

what is the simplest definition of ion exchange capacity

What this unit identifies for the ion exchange capacity ca. 0.92 meq. g-1. I am a newcomer in the membrane area. I just started. I highly appreciate your help

08 May 2021 0 0 View

what is the simplest definition of ion exchange capacity

What this unit identifies for the ion exchange capacity ca. 0.92 meq. g-1. I am a newcomer in the membrane area. I just started. I highly appreciate your help

08 May 2021 0 0 View

i have some problem with chtMultiRegionSimpleFoam

--> FOAM FATAL ERROR: Maximum number of iterations exceeded From function Foam::scalar Foam::species::thermo::T(Foam::scalar, Foam::scalar, Foam::scalar, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar) const) const [with Thermo = Foam::hConstThermo >; Type = Foam::sensibleEnthalpy; Foam::scalar = double; Foam::species::thermo = Foam::species::thermo >, Foam::sensibleEnthalpy>] in file /home/ubuntu/OpenFOAM/OpenFOAM-4.1/src/thermophysicalModels/specie/lnInclude/thermoI.H at line 66. FOAM aborting #0 Foam::error::printStack(Foam::Ostream&) at ??:? #1 Foam::error::abort() at ??:? #2 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::calculate() at ??:? #3 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::correct() at ??:? #4 ? at ??:? #5 __libc_start_main in "/lib/x86_64-linux-gnu/libc.so.6" #6 ? at ??:?

24 March 2021 0 0 View

Can we classify HV and LV lines based on line length?

I have dataset which shows the length of power lines. I need to classify the lines based on the line length. Is there a rule to classify the High voltage (HV) and low voltage (LV) lines based on...

03 March 2021 4,116 4 View

What is the production process of CaFe ferroalloys?

I looking for ferro calcium production process

03 March 2021 1,755 4 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Which is suitable for use with Python? MySQL or SQL Server?

Which is suitable for use with Python? MySQL or SQL Server? What is your suggestion?

01 March 2021 3,422 3 View