What is the relative permittivity of the plastic material used in laptops (a.k.a. PC+ABS-FR(40)) from 600 MHz - 6000 MHz?
if we are doing non-invasive sensing in patient urine then require ethical permission or not??? If we have a consent form fill with the patient then it is sufficient or not???
24 May 2024 956 0 View
My CV profile shows redox peaks at around -0.3V in the potential window -0.7 to 0.3V. But in GCD, the discharge curve is not going below -0.25V. If the potential window of GCD is followed i.e....
29 January 2024 9,836 3 View
I am trying to join 2 brass sheets of 0.2 mm thickness (each) at the edge. Is there a good low temperature solder such as indium which can provide hermetic sealing? I am trying to determine the...
25 January 2024 9,836 2 View
Can we partly cure Butyl rubber sealant formulation at room temperature in 10-15 days time. The purpose of adding a curing system in the formulation is to add the tensile in the product without...
24 January 2024 3,285 3 View
Hi Can anybody help us to know how we can make zinc disorbate ?
23 January 2024 3,884 1 View
Since its multidose injection, we have benzalkonium chloride as preservative in formulation. we knew that benzalkonium chloride also act as cationic surfactant. During stability, How to avoid the...
01 January 2024 2,610 3 View
In my study I have observed that the capacitance retention rate after 1000 charging-discharging cycles increased beyond 100%. can anyone kindly provide insight in this regard. Thank...
21 December 2023 2,848 1 View
The amount of reagents to be taken
02 December 2023 3,481 0 View
procedure of preparation
19 November 2023 4,484 1 View
Currently, I have a global variable array and I can also plot it in the calibration window but I want to plot each data sample by a delay of 2.5 mili Seconds which means after one data sample next...
16 November 2023 2,544 2 View
I am not able to get good literature and the physics behind how first these grains and grain boundaries arises out of no where when we make a pellet to study its dielectric properties and then how...
07 August 2024 5,177 3 View
I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...
05 August 2024 454 3 View
Suggest one of them 1. Teflon-lined stainless steel autoclave: 2. Alumina (Al2O3) ceramic container
30 July 2024 7,326 1 View
Hello everyone, I am new to this characterization but watching videos on youtube I have already plotted a Nyquist plot (Z' and -Z'') and already fitted models on my material using Zsim. But now I...
29 July 2024 1,376 0 View
Hello, dear colleagues, I would like your help in finding a reference that provides an average water savings due to plastic recycling compared to the consumption of virgin materials, preferably...
29 July 2024 4,630 0 View
Hello everyone, I am currently pursuing a PhD in Environmental Engineering with a focus on microplastic studies. My background is in Civil Engineering, and I am relatively new to working with...
18 July 2024 7,258 3 View
In general, the characteristic of electric current as a function of voltage in argon plasma jet using dielectric barrier discharge in atmospheric pressure, jet length will increase by the increase...
16 July 2024 9,316 1 View
Could you provide information on the average energy consumption per gate operation when using superconducting qubits, specifically focusing on the microwave power required to implement gates? I...
15 July 2024 954 0 View
We're studying the stability and fusion behavior of multiple PVC compounds in a Brabender. After a few trials, we set the temperature at 195 °C and the rotor speed at 70 rpm. Samples differ in...
12 July 2024 2,768 1 View
I want to reduce simulation time in CST for frequency domain solver by upgrading my computer. I already have discrete GPU but it doesn't seem to make any difference at all compared to integreted...
10 July 2024 2,789 4 View