In PRIMER, is it possible to downweight certain taxa in multivariate community datasets to reflect uncertainty around identification??

I have a dataset with about 80 different species. As usual, some species are very easy to identify with certainty whereas others are more difficult, which means that I am less certain of my...

03 March 2021 8,066 4 View

How to get onecolumn document from standard IEEE ACCESS LateX template?

I have prepared a manuscript in IEEE Latex template, but for some purpose, I need to prepare a word file as well (detailed format is not required). Compared to two column .tex file, one column...

02 March 2021 1,830 3 View

Gel electrophoresis result for total RNA samples, 1.5 Agarose gel was used, How to improve the integrity of RNA?

Gel electrophoresis, RNA degradation, RNA extraction from fresh tissue

02 March 2021 5,433 5 View

How to grow E.coli on the low salt LB agar plate with 50 or 100ug/ml of Blasticidin?

Hello, I would like to ask how to grow E.coli which resists 50 or 100ug/ml of Blasticidin. I have tried many methods by using low salt Luria-Bertain(LB) agar plate. However, no colonies grow. Let...

01 March 2021 2,027 2 View

OpenBCI eeg--has anyone used them?

I'm looking to try out an off-the-shelf EEG set for some exploratory work. Curious if anyone has used the OpenBCI, and how much set-up work is required. I've heard they are more difficult to get...

01 March 2021 4,128 3 View

How to remove DCU and HOBT from my reaction?

I am doing a acid and a chiral amino alcohol reaction using DCC and HOBT in DCM or THF? Can anyone suggest me how to remove DCU and HOBT from a reaction mixture??

28 February 2021 2,153 1 View

1 nm thick MgO thin-film to be deposited on Si wafer using thermal evaporation. What will be the optimum deposition conditions?

Favourable conditions of base pressure, rate of deposition. Also, by which characterisation technique to be used to verify the thickness of the deposited film.

28 February 2021 3,640 3 View

How to eliminate Steady state error from Reinforcement learning genetic algorithm code?

The following code (see 1st 2 images attached) is used to produce PID controller values that are designed to control the system (G). The code finds the PID controller values (noted as k) by using...

28 February 2021 6,560 14 View

B-mercaptoethanol (BME) protocol?

Hi everybody, I have been running a multiplex IHC which allow me to stain the same tissue with different markers (Primary Ab + Secondary conjugated Ab) (AF487, AF555, AF647). Since I would like to...

27 February 2021 5,028 2 View

What is the suitable range of Sulfur content and Viscosity of Heavy fluid Oil that used in Kiln?

What is the disadvantages of high sulfur content to the ceramic burning process? and what is the effect of outranged viscosity?

24 February 2021 8,219 2 View

Buffer Exchange using column packed with sephadex G-25 effect on protein concentration?

Hello, If i am doing a buffer exchange for an antibody of 1mg/mL, does the elution lose protein in the process of buffer exchange? For example, if i flow through 500 uL of 1mg/mL sample, and...

03 March 2021 6,299 3 View

No title

03 March 2021 5,360 2 View

How to normalise data on OPM package from R Studio ?

Good afternoon, I recently used OmniLog from BIOLOG for my experimentations : I tested the metabolism of different strains on 2 types of plates. I have 16 strains of 3 different groups...

02 March 2021 3,584 1 View

Timeout error!! Processor in the loop (PIL) using STM32F4 Matlab 2018a?

Dear Researchers I am trying to perform a PIL simulation using STM32F4 Discovery board and comunication serial USB TO TTL. During simulation I receive the following timeout error: An error...

01 March 2021 2,327 1 View

How can we raise the figure when we writing a paper with Latex ?

Hi, everyone. I'm a starter to write a paper by Latex. But I have some difficulty using it. I'm writing the paper with 2 columns. And, there is one figure that occupies the 2 both-sides. I want to...

26 February 2021 3,738 3 View

What is the best way to calculate the angles of twist for concrete columns subjected to torsional moment using finite element software?

In Finite element software like ANSYS , there is difficulty in obtaining direct results of twisting of concrete members because SOLID65 which is the unique element designed to represent concrete...

26 February 2021 3,806 2 View

How to plot the probability paper of Gumbel distribution using R programing?

In R-studio, there are many commands of Gumbel package. Arguments are also different. I`m asking about the alpha parameter of the Copula which must be greater than 1. If this is the one used to...

25 February 2021 5,229 3 View

Has anyone had luck using cell lines other than HEK 293 (such as COS1) to package lentivirus?

I am looking to package lentivirus in endothelial cells but I am opposed to using 293 cells due to personal ethics regarding the source. I have done some reading and saw that COS1, COS7, & CHO...

25 February 2021 3,030 1 View

No title

I am trying to find how to know the density needed for a pva electrospinning in a 0.6mm neddle, the electrospinning will be from top to bottom and the problem I really have is the solution because...

25 February 2021 2,615 3 View

Compute for the total volume of concrete needed for the concrete pouring of the foundation including its column up to NGL only as shown in the plan?

Looking for the quantity of cement, sand, and gravel of footings and columns. Thank you!

25 February 2021 3,092 2 View