The change in boundary conditions lead to different cases, sometimes settlement is low values and may be large values when change boundary conditions. What is the best simulation of boundary conditions that gives results near to the real case?
if we expose the fish after acclimatization to particular toxin in order to find out LC 50 (96 hours).Should we keep the fish off feed or with feed for that duration. Some literature show that...
24 February 2021 357 2 View
22 February 2021 2,588 2 View
The pandemic has led to depression and anxiety and its negative effects shouldn't be ignored. However, it has also led some people to become more resilient! What do you think? Thank you.
21 February 2021 4,733 19 View
We have a research project consisting of three variables where big data is the independent variable. Some previous studies showed that Volume, Variety, Velocity and Veracity Are the dimensions...
21 February 2021 8,133 2 View
I have a direct band gap material and an indirect band gap material. If I made a composite of both through physical mixing. Then how can I determine the band gap of such a material as the Tauc...
17 February 2021 8,104 4 View
the samples are not completely soluble - just swelled the solvents that's mean the sample may be partially soluble any suggestion, please
16 February 2021 8,801 3 View
i want to implement pseudo random number generator in matlab ...i request to every one if someone have code these PRNG share with me SplitMix Permuted Congruential Generator (PCG) Random...
14 February 2021 6,828 7 View
I am working on a biosensing project on paper substrate, however, it is found that the RNase contamination occurs on the filter paper. Might I ask is there any method to clean the paper surface...
12 February 2021 3,926 3 View
Hi everyone, I would really appreciate it if someone can tell me when and why a raw fluorescence starts below zero. In the picture attached below the blue colour curve starts from a negative...
09 February 2021 4,642 3 View
This is a follow-up on an earlier question regarding mechanistics of vaccines: why current vaccines don't block transmission. In summary, they don't engage mucosal immune cells to produce IgA....
08 February 2021 8,321 3 View
Actually, I am running cfd simulation for a heat exchanger which has two fluids one hot and other one is cold fluid. there is a solid domain between them, which I removed and instead I have used...
01 March 2021 9,537 2 View
I am simulating Heat Exchanger. I have tried and tested all the methods to resolve this issue from the internet like refining mesh, improving skewness and orthogonal quality ,extending outlet to...
01 March 2021 6,985 3 View
Hello, I have used the shell function on SpaceClaim to create thin solids for the model I am studying. These are contained within an enclosure for my study. I chose this approach as it avoids the...
24 February 2021 8,856 3 View
I am using Abaqus to simulate a plate with in-plane loading. The boundary conditions allow the right edge to move up and down, the displacements on the left edge are fixed. There is no rotation...
23 February 2021 711 3 View
Dear researchers, I want to simulate a flow (air) in a wind tunnel, and I want to integrate a fluidic actuator inside it in order to control the separation of the boundary layer. At the blower...
22 February 2021 4,882 3 View
Hello, I created a very tall tower (>1000m) and applied pressure boundary conditions at the inlet (bottom) and outlet (top) that correspond to the pressure are their relative altitudes....
22 February 2021 9,972 4 View
I am trying to simulate a simplified version of a beam resting on 10 points using Abaqus. The solutions I want to obtain are the Reaction Forces in each resting point or area when applying a...
21 February 2021 3,075 2 View
Hello I am trying to simulate crawling motion of a bilayer beam using Abaqus. Kind of similar to this: https://youtu.be/os-Z3ucoFpA I am using multiphysics enabled (diffusion, deformation,...
20 February 2021 2,916 1 View
I am running analysis of a cross-shaped sample that is prescribed a displacement along x and y-axes. I have run several jobs with this model and had no issues. However, the current set of...
15 February 2021 1,680 8 View
I am working on modeling of Direct Contact Membrane Distillation system with COMSOL Multiphysics software. I have some problems with the mass transfer part of the simulation because I don't know...
14 February 2021 379 2 View