What is the best type of mesh for explicit dynamic problem(shocking) in ansys-workbench ?

22 February 2016 0 5K Report

The type of mesh affects only the accuracy or affect the result in general

Badges
Science topic

More Nebras Shash's questions See All

How to solve "java.lang.ArrayIndex OutOf Bounds Exception: 0" error in ImageJ ?

It happened to me while I was using an ImageJ plugin. I got the error but the issue I don't know how to reach the array code to solve it.

02 August 2022 3,922 1 View

How to define all the parameters modified johnson cook model in LS-Dyna?

I'm doing a project about high velocity impact simulation using LS-Dyna and i got a problem about modelling the material modified johnson cook MAT107. I have all parameters material using modified...

13 February 2016 2,928 4 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

Tangential stiffness option in ansys workbench?

I am not able to find how I can provide tangential stiffness in ansys workbench The normal stiffness option is there. But how I can enter tangential stiffness I have read somewhere tangential...

29 July 2024 2,032 2 View

How to Import Blade geometry from CAD file in ANSYS design modeler?

Hello. I have the geometry of a blade in CAD file (stp) and I want to prepare the blade for meshing with turboGrid. I must import this file into designModeler and then transfer to the...

27 July 2024 356 3 View

Which software tools are best for enhancing diagnostic accuracy in chest X-ray imaging using image reconstruction and neural networks?

I am reaching out to seek your valuable advice and recommendations regarding the best software tools to use for this research. Specifically, I am looking for software with a user-friendly...

22 July 2024 3,794 1 View

How can I extract the mathematical equation from existing Neural Network Model?

There exists a neural network model designed to predict a specific output, detailed in a published article. The model comprises 14 inputs, each normalized with minimum and maximum parameters...

14 July 2024 2,714 3 View

Why my simulation results are showing too much deformation compared to experimental result?

I performed fea on tensile dog bone specimen using ANSYS static structural and also tried using ANSYS explicit dynamics. In experimental result the load is 500 N and deformation is 0.6 mm...

13 July 2024 3,631 4 View

Can I transfer the 3D file from Matlab to Ansys or Abaqus?

I have a 3D output in the figure section of Matlab, does anyone know a way to transfer it to Abaqus or Ansys? Or in what format should I save it so that these analysis software can analyze it?

09 July 2024 9,226 3 View

What is the current status of augmented learning in robotic surgery?

I would like to perform a literature review at this time on augmented learning and learning augmented algorithms to enhance performance-guided surgery

06 July 2024 246 1 View

How to solve the question of ansys fluent?

Regarding the system coupling issue where the update of the solution component fails, the system coupling update for fluid flow (Fluent) triggered an exception: "Update Solution Failed."

30 June 2024 7,894 1 View

The value of RF3(Z) in Abaqus model is huge how to control that?

I am modelling CFS Sheath wall in abaqus and i am applying the 100 mm displacement but i am getting high reach force close to 150 kN but i need it till 50kN. I have used mesh independent fastner...

27 June 2024 4,212 2 View