29 August 2020 4 2K Report

Dear all,

I want to know the best method to select the pseudo-absences between : minimum Convex Polygon method, kernel density estimate and from the buffered area around the occurence points. Any other suggestion will be welcome.

Thank you in advance

Best regards

Ilhem

More Ilhem Bouderbala's questions See All
Does anyone use lippmann's 4 point light 10W resistivity meter for groundwater investigation?

Dear colleagues, Does anyone use lippmann's 4 point light 10W resistivity meter for groundwater investigation? for VES AND ERT.

19 October 2023 1,423 4 View

What are the main things that can help a review article get published, even though it can be very challenging to do so?

What are the main things that can help a review article get published, even though it can be very challenging to do so?

07 May 2023 9,600 4 View

ERROR in command readElementFieldOdb?

Hello, I work on cyclic loads and i want to repeat 1000 times the job output from Abaqus (containing 2 steps). For that i'm using a code in the Abaqus2Matlab to read at first ODB. I'm trying this...

24 August 2022 4,255 0 View

Is anyone working on a Green Human Resource GHRM?

Is anyone working on a Green Human Resource GHRM?

05 February 2022 5,144 13 View

How we can remove nitrates of groundwater ?

We have a water source contains a concentration of nitrate 150 mg/l which is very high level. we would like to use this resource of 5 l/s in the drinking supplies. What you recommand me as a...

16 November 2019 5,694 21 View

is it possible to give weights to the parameters of GOD method?

i want to create weights for GOD method

11 March 2019 3,069 5 View

Are there any works that prove the positive relation between the diel vertical migration speed and the cells survivability?

Dear all, Are there any works that describe the positive relation between the diel vertical migration speed and the cells survivability for phytoplankton cells? Thanks you in advance Best...

07 December 2018 3,301 2 View

How to simulate particles motion with reflecting boundaries?

Dear all, I want to know the different possibilities of how to simulate the particles motion with reflecting boundaries. Means that if the next location goes out form the domain, so what are...

02 May 2018 7,805 9 View

If you have any scientific papers about drainage systems used to resolve and treat the problem of high soil salinity ?

Please, if you have any scientific papers about drainage systems used to resolve and treat the problem of high soil salinity (EC > 6 mS/cm) send them to me ? Vertical drains, bio-drainage,...

08 January 2018 2,429 13 View

Do the phytoflagellates produce and excrete the TEP (Transparent Exopolymer Particles) as diatoms?

Thank you in advance Ilhem

26 October 2016 6,271 2 View

Similar questions and discussions
How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

Measuring the Intelligence of a Species?

Larger brains, which typically contain more neurons, store and transfer more information (Tehovnik and Chen 2015), but the precise relationship between number of neurons and information has yet to...

05 August 2024 1,238 2 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

What are the shear and normal stiffness values of an LLDPE liner in 3D numerical modeling of a stockpile?

I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...

05 August 2024 3,665 0 View

Why results of ROS flurescence are negative as there was no bacteria within?

Hello. I am working on ROS production of two systems: system A is cerium oxide and hydrogen peroxide, system B is cerium oxide nanoparticle, hydrogen peroxide and potassium bromide. I did some...

04 August 2024 5,974 3 View

Our partners will collect data and use cookies for ad personalization and measurement. Learn how we and our ad partner Google, collect and use data. Agree & close