I would like to mesh the human lumbar spine with hexahedral elements in HyperMesh/HyperWorks. Does anyone know a good article which describes the steps or even show it?
Any help will be highly appriciated.
I want to know more about Uranium ore deposits in world.
11 August 2024 6,720 0 View
I want to know more about diamond ore deposits in world.
11 August 2024 2,167 1 View
We assume that the difference is huge and that it is not possible to compare the two spaces. The R^4 mathematical space considers time as an external controller and the space itself is immobile in...
10 August 2024 6,678 14 View
If Banks do not provide credit facility, what are the options available for FPOs and impact on producer’s income?
10 August 2024 8,198 5 View
I used eye tracking to examine how participants from two different populations (A and B) react to an image. Participants in population A exhibit larger pupil sizes over time, but they also have...
10 August 2024 3,229 0 View
What are a “Farmers Producer Organization” (FPO) and its essential features?
10 August 2024 477 5 View
I have been doing the m6A dot blot for a while with no improvement, I am extracting the RNA, and I can see the dots although the three biological replicas give a different reading on the memberan...
10 August 2024 8,539 5 View
How do interactions between the biosphere, the carbon cycle, and the water cycle impact global warming and interaction between the atmosphere and the hydrosphere?
09 August 2024 3,291 2 View
I have input a moment load in module load Abaqus, i put my moment load on the node surface (using reference point). I have define moment in history output and make a set for moment too. But the...
08 August 2024 4,831 4 View
How is energy cycled through the Earth's climate system and how do matter cycle and energy flow through the rock cycle?
08 August 2024 8,162 0 View
I am modelling CFS Sheath wall in abaqus and i am applying the 100 mm displacement but i am getting high reach force close to 150 kN but i need it till 50kN. I have used mesh independent fastner...
27 June 2024 4,212 2 View
For the article, I need some references for the subject of checking the convergence of the temperature field parameter for the SPH part in Abacus, and I want to study this case with a few meshes...
13 June 2024 2,504 0 View
Why Spine gourd fruit become red while it is tender ? No attack of insect pest is recorded.
11 June 2024 8,771 0 View
Hello. I am trying to do contact-separation mode TENG. I have been following , and I am suffering to calculate the Open circuit voltage (Voc). I made geometry and set the materials setting all...
26 May 2024 2,645 0 View
Hi all, Here’s a simple but still very important (I think!) question regarding the philosophy of mesh overlap in open ventral hernia… I’m keen to clarify the concept of transverse diameter mesh...
25 May 2024 4,744 2 View
Hello I am trying to simulate 2dof cylinder for VIV analysis and I used an FDM method but the cd and cl values i got are so high and the damping is not coming into picture i tried and modified the...
17 April 2024 4,597 0 View
Recently, I was working on cell biology of spinal ligement tissues, the human samples obtained from spinal surgery were easy to identify, but how can I make sure of the isolated spinal tissues...
02 April 2024 2,674 0 View
Dear Sir/ Ma'am When I am considering the human model with an antenna for simulation in CST then it is reflecting an error as "Time domain solver does not support mesh size > 2 billion mesh...
29 March 2024 8,205 1 View
1.Fixed boundary condition at both end of the pipe elbow. 2.Pressure applied is 30 Mpa. 3.Hex ,sweep mesh applied.
18 March 2024 5,935 2 View
I am currently conducting an analysis on a wind turbine and I am trying to input periodic boundary conditions in the mesh and it keeps showing me the same error which is the meshing algorithm...
13 March 2024 9,826 0 View