Difference between Data-Driven Adaptive Robust Optimization and Adaptive Robust Optimization?

Could you make some points about the difference between Data-Driven Adaptive Robust Optimization and (classic) Adaptive Robust Optimization?

01 November 2020 9,653 3 View

Can anyone send me some data about paleoclimate of Asia? Especially the climate of Asia in LGM, LIGM, and mid-Holocene time periods?

Hi I need some data about paleoclimate of Asia especially the climate of Asia in Last Glacial Maximum (LGM), LIGM (Last Inter Glacial Maximum), and mid-Holocene time periods? Please can anyone to...

03 August 2020 4,089 1 View

How I can see contact stress in my analysis result in abaqus ?

I want to report contact stress in my result, is that cpress (contact pressure) ? what is the different between contact stress and contact pressure? !

27 July 2020 3,767 3 View

What is this Error in MaxEnt software?

I did layer clipping but maxent software gives error with them. There is the picture of error in attachment. Please can anyone help me? What is problem in MaxEnt software? Is my clipping incorrect?

09 October 2018 8,906 0 View

Is there consciousness only in living creatures with a neural system?

Is it possible to extend the definition of a kind of consciousness for plants, fungi and bacteria? I am looking for any logical answer, please don't hesitate to contact me.

21 December 2017 4,520 13 View

How can I find and extract Email of numerous scientists in a particular branch of science from the Internet in a short time?

I am looking for any correct answer, please don't hesitate to contact me.

14 December 2017 5,048 3 View

What is the mutation rate in the mitochondrial genomes of the family Bovidae?

I want to determine the phylogenetic age of the members of the subfamily Hippotraginae (Bovidae) based on complete mitochondrial genomes, using BEAST software; But I do not have a good indicator....

11 December 2017 2,497 9 View

What is the mutation rate in the mitochondrial genomes of the family Bovidae?

I want to determine the phylogenetic age of the members of the subfamily Hippotraginae (Bovidae) based on complete mitochondrial genomes, using BEAST software; But I do not have a good indicator....

03 December 2017 3,347 8 View

Can anyone help with the following error in comsol?

08 February 2015 2,081 1 View

Does the pressure(-600 mmHg) affects pH?

When I conducted the degassing experiment using decompression under anaerobic condition(and I used ferrous based chelating agent), the oxidized ferric were observerd. So, could you tell me the...

03 March 2021 4,892 5 View

What are the new 2D nanomaterials were used for Silver nanoparticles stabilization?

In the stabilization of AgNPs are vital in current research interest. However, some of the 2D nano-materials like graphene oxide, MoS2, etc... previously used to stabilize it. But still they shown...

01 March 2021 2,207 3 View

1 nm thick MgO thin-film to be deposited on Si wafer using thermal evaporation. What will be the optimum deposition conditions?

Favourable conditions of base pressure, rate of deposition. Also, by which characterisation technique to be used to verify the thickness of the deposited film.

28 February 2021 3,640 3 View

Thermal reduction of graphene oxide.?

I am trying to reduce graphene oxide by thermally but I have no proper information regarding this. Can any one help me regarding the details about temperature and time for the reduction of...

23 February 2021 4,155 4 View

Is there an ideal incubation time of RGO-modified SPCE before subsequent use, i.e., electrochemical characterization or further modification?

I notice that upon washing and air-drying of my RGO/SPCE surface and characterizing again via DPV, the current response towards ferricyanide probe significantly decreases. My worry is that the...

22 February 2021 5,324 3 View

How can I measure the thickness of thin layers deposited on textured glass susbtrates?

I want to measure the thickness of aluminum oxide and titanium oxide layers deposited on textured glass substates. The layer thicknesses are typically below 100nm.

21 February 2021 5,465 4 View

What is the best etching method for Mg-Ca alloy?

I have used Picral etchant (4.2 g Picric acid, 10 mL Acetic acid, 70 mL Ethanol, 10 mL distilled water) but it didn't work. Is there any alternative?

21 February 2021 2,558 5 View

Color of spiro-ometad film?

What does the color of a spiro-ometad film indicate? I got purple, green, red, even black color of the spiro film. Is there anything we can get from the preliminary color analysis(e.g. oxidation...

21 February 2021 1,831 4 View

Which compound is getting oxidized during bulk electrolysis with TFAA?

The experiment is really simple. When I do a bulk electrolysis with 1% TFAA (ACN solution) to get dihydrogen, what is going to be oxidized? (working electrode graphit, counter electrode platinum,...

18 February 2021 4,430 1 View

What is the best substrate for exfoliating few layers of hexagonal boron nitride (hBN) using traditional scotch tape method?

Unlike graphene, it is usually very difficult to exfoliate few layers (~10 nm thick) of hBN on SiO2 substrate due to lip-lip interaction at the edges. Au substrates have been proven very useful...

16 February 2021 2,635 2 View