What is the actual role of metallic buffer layer in SBD?

More Gaurav Malik's questions See All

How can I increase the porosity of ITO coated glass substrate?

Can anyone tell me the process for making a porous ITO coated glass substrate.

31 December 2018 4,338 7 View

What is the effect of post annealing treatment on the thickness of the film?

Post annealing is an important parameter in thin film fabrication, which can help to enhance the physical, optical and electrical properties of the thin film by changing the microstructure and...

11 December 2018 3,475 4 View

Choice of the appropriate electrolyte for electrochromic behaviour of the metal oxide thin film ?

I am working on the electrochromic behavior of the metal oxide thin films. But, the literature suggests various electrolyte for this work. I am confusing about this. Anyone suggests the criteria...

08 September 2017 8,005 6 View

Buffer to disrupt platelet alpha granules for PF4 quantification?

Hello! I want to quantify by ELISA the secreted (from platelets poor plasma) and the non-secreted (from platelet lysate) PF4 before and after TRAP stimulation. I will use the ELISA from R&D...

03 March 2021 1,499 2 View

Buffer Exchange using column packed with sephadex G-25 effect on protein concentration?

Hello, If i am doing a buffer exchange for an antibody of 1mg/mL, does the elution lose protein in the process of buffer exchange? For example, if i flow through 500 uL of 1mg/mL sample, and...

03 March 2021 6,299 3 View

How optimize the Size Exclusion Chromatography?

Hello! I'll do a size exclusion chromatography, but I only have an open column, and I'll perform the peptide extraction from yeast, using buffer lysis (sodium phosphate 50 mM/NaCl 30 mM/DNAse and...

01 March 2021 2,215 2 View

Why are my bands weird in this Agarose gel?

Can someone please give me some possible things that could go wrong? Here is my recipe: 0.5g Agarose 50 mL of TAE 1x 1 uL ethyl bromide. Gel was run at 100V for 1 hour. The buffer used is also TAE.

01 March 2021 9,952 3 View

What do I do with DLS peaks that are from the buffer?

I'm looking at the aggregation of my protein sample using DLS. Unfortunately, my buffer (20mM HEPES) also results in a set of peaks. These are at approximately 1 and 1000 d.nm. The lowest peak...

01 March 2021 9,015 2 View

What is the most suitable resuspension buffer for TCA/acetone precipitated protein?

I need to extract protein from fermented carbon sources for Bradford assay. Most researchers experiencing insolubility of pellet in resuspension buffer. Please assist me to select most suitable...

26 February 2021 7,129 3 View

What urea buffer can i use for biotagged protein extraction from streptavidin beads?

Hi all, I have been doing research on biotagged LDB1 proteins in Mel cells. I purify the proteins using M280 streptavidin beads. The yield is very low so I've been trying to optimize it by...

24 February 2021 5,749 3 View

Cloudy/high background western blot - can anyone help me?

Hi everyone! I try to detect VDR protein (~48 kDa) using Western Blot. After SDS-PAGE using 10% MP TGX Stain-Free Gel from BioRad I transferred the protein onto an metOH activated PVDF membrane...

23 February 2021 6,266 3 View

How to improve the buffer capacity of sea water?

Hello everyone I would like to improve the buffer capacity of seawater (pH ~8) in order to dissolve as much CO2 as possible without dropping the pH below 7.5 (a range between 7 - 7.5 is...

17 February 2021 2,797 2 View

Why does flow deformation occur at the test line and control line on nitrocellulose membranes (LFIA)?

I use 1% BSA in 10 mM phosphate buffer (pH 7.4) solution when striping my nitrocellulose membranes with antigens and antibodies. However, I always observe deformed flow when my sample or running...

16 February 2021 4,224 3 View

Satyendra Mourya

Dear Malik, will you please give more details about the buffer layer and SBD device architecture?

Gaurav Malik

Dear Mourya, I am interested in ZnO/metallic layer/Si type architecture for schottky diode application. Is it beneficial or not ?. If it is beneficial than what will be the role of metallic layer thickness on device performance.

Isam Eldin Hussein Elgailani

Please look at the following below links which may help you in your analysis:

https://d-nb.info/1023816695/34

https://pdfs.semanticscholar.org/96ae/255222ac00375fdb3610a02e1593876b9564.pdf

Thank

Thanks to all for their valuable suggestions.