What is surface energy of a particle?

Dhanashekar Manickam @Dhanashekar_Manickam3

03 March 2015 1 697 Report

In a Ash prepared from a bio-organic matter how to determine the surface energy for it. Please share the supporting files.

Sarwan Kumar Dubey

My Dear Dhanashekar Manickam, Surface energy, or interface energy, quantifies the disruption of intermolecular bonds that occur when a surface is created.

http://en.wikipedia.org/wiki/Surface_energy

http://journals.aps.org/prb/abstract/10.1103/PhysRevB.1.4555

http://scholar.google.co.in/scholar_url?url=http://www.sciencedirect.com/science/article/pii/S0021850204003295&hl=en&sa=X&scisig=AAGBfm04arRkNGU-19s33_8iD1bQJp2iew&nossl=1&oi=scholarr&ei=_zgYVbiUM8HsmAWQiYKgDg&ved=0CB8QgAMoATAA

http://scholar.google.co.in/scholar_url?url=http://140.123.79.88/~ppmpk/paper/36-b.pdf&hl=en&sa=X&scisig=AAGBfm1e2A3ihIE9unlblTqi9hjXBOVbig&nossl=1&oi=scholarr&ei=_zgYVbiUM8HsmAWQiYKgDg&ved=0CCAQgAMoAjAA

Badges
Science topic

More Dhanashekar Manickam's questions See All

What is the relation between hardness and compression strength of Aluminium material?

Whether there is any valid relation between hardness and compression strength of a material. Please share your supporting article.

06 July 2017 9,545 3 View

What is the difference between these two alloys AlMgSi and AlSiMg ?

Whether these alloys are same or different. Please share relevant document.

04 May 2017 2,336 1 View

Where can i purchase LM25 alloy in rod shape ?

Am in need of LM25 alloy in as cast condition in the form of ROD shaped of diameter between 10 mm to 15 mm and a length of 500 cm. Any information you can provide me would be greatly appreciated.

11 December 2016 1,614 2 View

Classification of sliding speed/ velocity in tribotesting?

How to fix a range in setting the sliding speed/ velocity while performing a tribotest on aluminum composites. In specific what is considered as slow speed and high speed, how is it justified.

10 November 2016 8,868 3 View

Best heat treatment method for Aluminium metal matrix composites ?

As we know there are various heat treatment methods (T4, T6, T7, T3 and T8) for modifying the properties of the aluminium alloys (grain modifier, varying solutionizing temperature, artificial...

09 October 2016 7,740 8 View

What is the effect of Graphite addition in Aluminium composites with respect to density ?

when i add graphite at three levels to my metal matrix composites, i get the density values initially increases and then decreases with graphite addition.

05 June 2015 10,035 11 View

Can anyone share ASTM E9-09 standard?

Standard test methods of compression testing of metallic materials at room temperature

04 May 2015 3,781 6 View

What are the phases of alloying elements present in A356 alloy?

In A 356, alloy Elements - wt% are:Cu - 0.02Si - 6.99Mg - 0.48Mn - 0.02Fe - 0.22Ti - 0.18Ni - 0.01Zn - 0.04Pb -

04 May 2015 1,627 6 View

How to calculate Volume fraction of matrix in a hybrid composites?

as there is formula to calculate the Volume fraction of the reinforcement as given in the attached journal page no:3. Now how to calculate Volume fraction of matrix when the composite have...

02 March 2015 7,537 8 View

What is the minimum diameter of the disk (Aluminium composites) used for Pin on Disk test?

I have fabricated the composites for an diameter of 50mm. I s possible to use this as a disk in wear test against the steel pin.

02 March 2015 5,586 5 View

How to develop investments in renewable energy sources?

08 August 2024 5,112 3 View

Which distribution type should I use when calculating the average particle size from TEM image? and how to calculate the error ?

average particle size calculation from TEM

04 August 2024 2,921 1 View

Who of all the Global Scientific community will help me Prof. Dr. Yoshida make way for TPEOM, MEC ~EMC to return the atmospheric gases to the norma ?

TEP presentation caption (The Environmental Project) Re: Why should Washington’s DC, or any country government point of location think of as nowadays of as to being 'tomorrow as to come! if it...

03 August 2024 2,484 1 View

How to load and plot 2D-PIV (particle image velocimetry) recorded velocity vector field in Techplot?

Dear Researchers I need to know, how to load and plot 2D-PIV (particle image velocimetry) recorded velocity vector field data in Tecplot? Thank You

02 August 2024 3,615 1 View

Does the delta function actually make sense to use on point particles?

The delta function seems produce logical contradictions when analyzed on a fundamental level. I would be curious if anyone else agrees.

31 July 2024 10,109 3 View

Is artifacts in XPS possible to build high deviation in binding energy larger than 5 eV??

Hello. Thanks for your consideration to see my question. Recently, I conducted XPS anaylsis of g-CN that is prepared from thermal polycondensation of DCDA, so-called conventional bulk-g-CN,...

30 July 2024 9,824 2 View

Is there a database with onshore wind production for the wind farms in Portugal?

I am looking to predict some production for future onshore wind energy production in Portugal, is there any database with info of performances of the existing wind farms in the country? something...

28 July 2024 1,750 1 View

HAs anyone used TGA to find activation enegy of water evaporation?

I have different polymer solutions and I hypothesize that water molecules are retained based on the water-polymer interactions, so the amount of free water is less to intercat with drug tablet....

28 July 2024 9,545 6 View

I found the zeta potential of exosomes in DLS and it was -8mv. So is it correct or not ?

What should be the zeta potential of bovine milk exosomes

25 July 2024 7,376 5 View

Can we eliminate the stress singularity at the tip of the crack by manipulating the elastic constants?

The aim of the research here is to prevent the propagation of the crack in the fabricated elastic medium with useful applications.

25 July 2024 9,976 3 View