13 June 2017 6 7K Report

I am studing about titanium powder.

More Swapnil Padole's questions See All
What does negative readings in spectrophotometer denote. Was testing TSS content of bacterial cultures?

I was performing estimation of Total Soluble Sugar content in bacterial cultures by Anthrone method. Out of 9 samples, only one sample showed positive reading while others had a negative reading...

22 July 2024 9,576 4 View

I am modelling resistance spot welding (2d) in comsol, so how to get nugget formation ?

I am using apparent heat method for simulation

14 June 2024 4,670 1 View

Does age of a bacterial culture have an impact on its DNA isolation?

Generally for bacterial DNA isolation we use a fresh culture of 2-5 days old. But if we use an older culture say 10-15 days old will it have any impact on the DNA content and the DNA isolation...

13 May 2024 3,061 11 View

Is it possible to perform three-way interaction effects and plot graphs (of different levels) using Jamovi Software?

I am trying to plot the three-way interaction effects using different levels of moderated-moderator (high, medium and low), But I am unable to figure a function for separating the information...

02 May 2024 6,924 0 View

What concentration of Nystatin should be used in Nutrient Agar medium?

I'm isolating bacterial from soil on Nutrient Agar media but after 4-5 days I see fungal growth start in the plates. I read about use of Nystatin to prevent fungal growth. How much quantity or...

21 April 2024 6,039 5 View

Why is my sub-cloning not working?

I have two different construct: 1. Insert 1 (~3kb) at XhoI and ApaI site in NCVB vector (9.7 kb). 2. Insert 2 (~1.7kb) at XhoI and ApaI site in in pENTR/D vector (2.6kb) I want to replace Insert 1...

09 March 2024 8,215 7 View

Why rheometer showing negative yield stress values ?

I am using ICAR rheometer for the determination of static yield stress for different resting times. I observed the negative yield stress values for initial period of time i.e for 5 min and 10 min...

10 October 2023 3,431 0 View

Which are latest theories or models in technology adoption by humans/users?

There are various theories/models which explain technology adoption by humans/users like CDT, IDT, TTF, EDT, TRA, TPB, SCT, TAM, TAM2, MPCU, MM, DTPB, C-TAM-TPB, UTAUT, UTAUT2 etc. These models...

05 October 2023 6,113 0 View

A part from HK Green dyes; can anyone suggest a dye or fluorescent probe to detect peroxynitrite concentration in plant samples?

HK green eyes are most suitable for the same but they're not available anywhere that's why I'm asking the question.

28 August 2023 5,803 1 View

In Bldc motor on what basis the stator slots number are decides?

I am doing motor designing.

24 July 2023 7,625 0 View

Similar questions and discussions
How to understand this crystallographic phenomenon of low temperature crystals in zeolite?

During low-temperature testing, new diffraction peaks that appear could be indicative of several phenomena. In one of our tests, we observed notable new peaks around 40° and 45° in a specific...

06 August 2024 726 3 View

Why Powder XRD is performed after cruhsing a crystal if Single Crystal XRD analysis of the same crystal has been performed already ?

What information we can get from PXRD analysis other than from SCXRD analysis of a crystal ?

30 July 2024 6,261 4 View

What should be the sample container for the hydrothermal reaction in a microwave reactor at 180 °C for 10 min at the heating rate of 5 °C per minute?

Suggest one of them 1. Teflon-lined stainless steel autoclave: 2. Alumina (Al2O3) ceramic container

30 July 2024 7,326 1 View

Is there a good macro photography kit for on-site metallurgical investigation?

I am looking to purchase a photography kit for onsite metallurgical investigations, such as capturing photos of worn areas, hot tears, cold tears etc. Could anyone suggest me a good...

22 July 2024 3,490 2 View

What could be the possible reason that sintering of polycrystalline diamond fabricated with tape casting has suddenly started failing?

I make polycrystalline diamond with tape casting followed by HPHT sintering. When i sintered the samples up till May, the sintering was good. When i sintered the samples in June and July at the...

16 July 2024 3,212 5 View

What binders suggestion that I can use for zinc alloy?

I am working on powder metallurgy, and during the compaction process, the powder does not pelletize and remains in its powder form. To address this issue, I am considering using binders to improve...

13 July 2024 9,003 2 View

What may cause whitish discolor of polycrystalline diamond surface, and cracks near edge?

I am preparing polycrystalline diamond (PCD) with tape casting. The powder is 8~12 um. After drying of tapes, I place several tapes in Ta cup without warm-pressing. Next, debinding is carried...

23 June 2024 7,758 2 View

Can anyone suggest an adhesive that can sustain 600C?

I have to join tungsten wire to metallic plate with that adhesive and entire assembly has to be heated upto 600C in ultra high vacuum. I know about zirconia paste but it is not readily available...

18 June 2024 3,092 3 View

Does the zirconium isotope fractionate as through the column?

Is the zirconium isotope of geological sample fractionated when passing through the column, and how to determine whether this fractionation is or not？

26 May 2024 6,721 2 View

How do we interpret the origin statement ?

Crystallography Doubt_International Table of Crystallography In the space-group number 185 of ITA (see Attachment), how do we interpret the origin statement?

08 May 2024 10,055 0 View

Our partners will collect data and use cookies for ad personalization and measurement. Learn how we and our ad partner Google, collect and use data. Agree & close