Hi,
Can any one please tell me, what is pressure strain elastic modulus and how to calculate it.
Hi, Is it possible to give specified shear for the wall in Fluent. I have checked the manual and found that the wall can be modeled in the following ways (For VOF model, only adhesion contact...
05 June 2019 6,670 3 View
Hi, I am trying to simulate the mucus removal process using Fluent. I used multiphase model (air+mucus), simulation is working fine for the no-slip condition. In the realistic case, mucus will...
05 June 2019 3,938 1 View
Dear all, Any body know how to give stress strain curve with negative slope in abaqus
02 March 2019 1,962 4 View
Hi, How to calculate 3 components of j integral using domain integral method.
04 May 2017 3,768 2 View
Hi, Is it possible to calculate displacement gradient matrix from strain tensor and gauss point co- ordinates
03 April 2017 1,635 3 View
Hi, How to calculated the Orthocenter of the triangle with 3D vertices A(x1, y1, z1), B(x2, y2, z2) and C(x3, y3, z3)
02 March 2017 1,710 3 View
Hi, Anybody please explain. How phantom node method is used in Abaqus XFEM implementation for cutting the element during crack propagation
10 November 2016 10,241 0 View
Hi, What is the difference between Generalized Finite Element Method and Extended Finite Element Method.
10 November 2016 9,976 1 View
Hi, I am trying to install abaqus 6.14 (abaqus 2016) in my workstation (client machine) Error is coming while giving licence server, can anybody help me in resolving this error Error: Unable to...
08 September 2016 8,208 5 View
Hi Everyone, I am trying to simulate crack propagation in abaqus and validating with analytical solution I need suggestions regarding what factors can to be compared/ considered for validating...
07 August 2016 6,247 4 View
I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?
11 August 2024 3,115 1 View
I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...
10 August 2024 4,005 2 View
How can I determine a good adhesion strength range for coatings on polymer surfaces, such as DLC on polymer substrates? Is there a specific threshold for adhesion strength (from T-peel tests)...
10 August 2024 942 3 View
Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...
09 August 2024 7,892 0 View
Fatal error in MPI_Allreduce: Other MPI error, error stack: MPI_Allreduce(1628)......: MPI_Allreduce(sbuf=000002459254A180, rbuf=000002459F86A140, count=4851, MPI_DOUBLE_COMPLEX, MPI_SUM,...
09 August 2024 7,615 1 View
I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...
09 August 2024 5,048 2 View
I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...
08 August 2024 719 0 View
Hi, I'm currently working on a project where I need to plot the atom-projected band structure using GPAW. I've been able to calculate the band structure for my material, but I'm having trouble...
07 August 2024 269 3 View
Hi all, my experimental XPS results shown that my C3N5 sample consists of N-H bond, hence in this case I should incorporate the N-H bond into my DFT modelling. However, I do notice several papers...
07 August 2024 8,414 2 View
I have been getting a low plasma and no coating while doing rf sputtering of copper doped ZnS using a power of 140 watts and at pressure of 6.5x10-3 Mb.
07 August 2024 4,526 4 View