What is Kinked Mach Stem problem?

08 August 2016 1 9K Report

I have found that researcher usually use this configuration for showing results of a scheme or a method. Is their any speciality in this model? What are the factors that need to be considered for design this configuration?

Zoubair Boulahia

Please look at this doc, it may be helpful.Good luck

Badges
Science topic

More Al Shahriar's questions See All

How to create mesh only on the curved surface of a cylinder in Gmsh?

When I create mesh on the following cylinder, it creates mesh on all the surfaces including the curved surface. But, I do not want to create any mesh on the top and bottom surface. // Gmsh...

03 April 2018 3,366 1 View

What is the way to give two inputs in a State-Space block in Simulink?

I am simulating an active quarter-car suspension system where road disturbance is one input and hydraulic actuator is another.

06 July 2015 9,958 0 View

How to calculate numerical flux through the domain near the solid wall for Euler equation?

I found a MATLAB routine, the code provided below, where numerical flux is calculated by using a method at the cell which share its face with a solid wall. And this numerical flux(H) is then used...

01 January 1970 258 5 View

Can you suggest litterature about upwind scheme used in modern CFD?

Actually i want some well organized documents on Upwind schemes that are used in modern CFD e.g. Flux splitting,Godunov scheme, TVD, Hartel Lax van Leer(HLL), etc. A book on techniques used in...

01 January 1970 322 5 View

How to learn more about SPSS and its Application?

I would like to learn more about SPSS and Its application especially in regards to data analysis. Please suggest me how I can learn more about it. Thank you so much.

11 August 2024 9,101 4 View

Can I base on reverse DNA sequences to perform alignment, convert to amino acids and GenBank submission?

I have reverse sequences (AB1 format), can I base on reverse DNA sequences to perform nucleotide alignment, convert nucleotides to amino acids and deposit the sequence in GenBank database?

11 August 2024 5,138 1 View

Baseline drift in HPLC? What causes this?

Hello, Why do i see this baseline drift when i compare my blank (black) to the sample (blue)? Any suggestions as to why this happened? Thank you!

11 August 2024 3,770 4 View

Text-Communication from the M1 Hand Area using BCI—and then there is Elon Musk?

Willett, Shenoy et al. (2021) have developed a brain computer interface (BCI) that used neural signal collected from the hand area of the motor cortex (area M1) of a paralyzed patient. The...

10 August 2024 7,180 0 View

Has anyone applied Python in the field of textile engineering for data analysis, automation, or smart textiles?

I'm currently exploring the application of Python in textile engineering, specifically in areas like data analysis, process automation, and the development of smart textiles. I'm interested in...

10 August 2024 7,429 2 View

How can I use the cif data obtained from rietveld refinement extracted via gsas2, for microstructural analysis using ETEX software?

09 August 2024 7,718 0 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

How are iso-frequency contours plotted?

Let's say we have a standard, regular hexagonal honeycomb with a 3-arm primitive unit cell (something like the figure attached; the figure is only representative and not drawn to scale). The...

07 August 2024 1,937 1 View

How to prepare the nanoparticle treated fungal sample for Environmental SEM analysis?

A fungal strain was treated with nanoparticles. We want to do an environmental SEM analysis. So could anyone share your views on preparing the sample? Thank you.

07 August 2024 5,307 1 View

How to normalize and take the significance of the MTT OD values with 3 replicates for the same cell-line?

Hi, I have a question about normalizing the MTT OD values for doing the statistical analysis. So, if we have 3 different plates and we call them 3 different replicates, so, first we would...

07 August 2024 8,106 4 View