Im planning to do the carburizing of my steel sample, but I want to prevent one part of it by copper plating and I was wandering if there is some indication about the copper coating created to be sufficient/properly dense/thick ?
I want to know more about Uranium ore deposits in world.
11 August 2024 6,720 0 View
I want to know more about diamond ore deposits in world.
11 August 2024 2,167 1 View
We assume that the difference is huge and that it is not possible to compare the two spaces. The R^4 mathematical space considers time as an external controller and the space itself is immobile in...
10 August 2024 6,678 14 View
If Banks do not provide credit facility, what are the options available for FPOs and impact on producer’s income?
10 August 2024 8,198 5 View
I used eye tracking to examine how participants from two different populations (A and B) react to an image. Participants in population A exhibit larger pupil sizes over time, but they also have...
10 August 2024 3,229 0 View
What are a “Farmers Producer Organization” (FPO) and its essential features?
10 August 2024 477 5 View
I have been doing the m6A dot blot for a while with no improvement, I am extracting the RNA, and I can see the dots although the three biological replicas give a different reading on the memberan...
10 August 2024 8,539 5 View
How do interactions between the biosphere, the carbon cycle, and the water cycle impact global warming and interaction between the atmosphere and the hydrosphere?
09 August 2024 3,291 2 View
I have input a moment load in module load Abaqus, i put my moment load on the node surface (using reference point). I have define moment in history output and make a set for moment too. But the...
08 August 2024 4,831 4 View
How is energy cycled through the Earth's climate system and how do matter cycle and energy flow through the rock cycle?
08 August 2024 8,162 0 View
How can I determine a good adhesion strength range for coatings on polymer surfaces, such as DLC on polymer substrates? Is there a specific threshold for adhesion strength (from T-peel tests)...
10 August 2024 942 3 View
I did PR spin coating on trench structure. I used AZ P4620 PR and the thickness or PR is around 11um. The substrate is Si. And my trench structure depth is 141um(negative way). Even though I...
08 August 2024 2,298 0 View
I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...
08 August 2024 719 0 View
I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...
07 August 2024 1,028 0 View
I have been getting a low plasma and no coating while doing rf sputtering of copper doped ZnS using a power of 140 watts and at pressure of 6.5x10-3 Mb.
07 August 2024 4,526 4 View
Suggest one of them 1. Teflon-lined stainless steel autoclave: 2. Alumina (Al2O3) ceramic container
30 July 2024 7,326 1 View
I am trying to coat my micelles and PLGA based nanoparticles with cell membrane using an Avanti mini extruder according to literature . I use 200nm membrane but my particles end up to be 400nm And...
30 July 2024 3,294 3 View
I've attempted to use this method to synthesize copper nanoparticles. Copper nanoparticles can be synthesised using a variety of precursor materials. CuSO4, distilled water, NaOH, and EDTA are...
28 July 2024 8,027 3 View
The catalytic effect of retained austenite refers to the phenomenon wherein quenching steels with a small amount of retained austenite, when subjected to tempering at a specific temperature...
27 July 2024 8,508 0 View
Please investigate the effect of temperature and strain rate of hot deformation and the formation of delta ferrite in martensitic stainless steel 410?
25 July 2024 9,408 0 View