I set the field functions for pressure and volume fractions, and the results are not quite right.
As described in the Multifractal detrended fluctuation analysis (MFDFA) algorithm, it at first calculates the profile of the time series, and then other steps are operated on the profile....
05 August 2024 9,365 2 View
Hi, Could someone explain the primary differences between deep-seated landslides and slope destabilization? In particular, definition and characteristics, mechanisms and triggering factors,...
02 August 2024 4,212 2 View
How long it takes for arbuscular mycorrhiza to establish and produce benefits under experimental conditions?
25 July 2024 5,207 2 View
Hi there, I did a CFA to 10 items on 2 latent variables. The model fit is too good and I've never seen it before. CFI / TLI = 1, RMSEA = 0. Is it okay, if everything else was done properly?...
24 July 2024 5,454 7 View
I want to study the thermal properties of a mixed system which is constructed by virtual crystal approximation in VASP. When I try to run the ab initio Molecular Dynamics of this system in VASP, I...
19 July 2024 6,568 3 View
If I want to invent my own hypothesis testing method, where should I get started ?
15 July 2024 5,375 5 View
I am currently working on a research paper focused on the control of Connected and Autonomous Vehicles (CAVs) utilizing multi-agent reinforcement learning methods. At this stage, I am seeking a...
14 July 2024 2,620 2 View
I've earned 1 best paper award and 4 best oral presentation awards. What should I do next to elevate my academic capabilities to the next level ?
14 July 2024 6,071 5 View
I read several information security books. How do I start writing anti-virus softwares ?
13 July 2024 8,180 1 View
I suspect my cells are contaminated with mycoplasma. I fixed the cells with 4% PFA and stained them with DAPI. Below is the image I obtained. I don't observe the typical small, rounded DAPI foci...
11 July 2024 7,786 3 View
I have been getting a low plasma and no coating while doing rf sputtering of copper doped ZnS using a power of 140 watts and at pressure of 6.5x10-3 Mb.
07 August 2024 4,524 4 View
Hello, I suspect that a molecule I am using is causing bacteria to experience osmotic shock. What chemical properties should I look for to compare this capability with those of other substances?...
06 August 2024 977 1 View
Hello I want to know about the sputtering condition of depositing FTO from target 95:5%. I tried with RF sputter in pressure 2.5Pa and 100 sccm Ar at room temperature but it showing no...
21 July 2024 1,680 2 View
I make polycrystalline diamond with tape casting followed by HPHT sintering. When i sintered the samples up till May, the sintering was good. When i sintered the samples in June and July at the...
16 July 2024 3,210 5 View
Hello everyone. I am working on my LV concentration porject, I use 500Kda hollowfiber to do it. The HCP and BSA removal rate is nearly 80%, but last time, I failed to run it. The HCP hasn't been...
11 July 2024 5,379 0 View
What will be the pressure in Iron Iron-Carbide diagram? It is at atmospheric pressure?
05 July 2024 1,891 0 View
Hi All, My name is Sumaiya, a PhD student at the University of Queensland. I am looking for some suggestions on how to hold mice and perform Randall-Selitto Test by using Paw Pressure Randall...
30 June 2024 6,004 0 View
I would like to dedicate my entire life in doing only one activity alone and nothing else. How do I achieve it in this world full of unavoidable distractions and societal pressures?
24 June 2024 298 1 View
While deriving for a momentum equation with elastic stress effects, I am planning to put a ratio between elastic modulus (in Pa) and dynamic pressure (in Pa) in a simplified form. I am not...
23 June 2024 8,059 1 View
Despite many attempts I am still unable to find the original version of this paper and would appreciate if anyone can locate it for us: Baker PG, Haig G (1981) Metronidazole in the treatment of...
20 June 2024 5,448 3 View