What are the solubilities of molybdenum sulfide and tungsten disulfide in glycols?

02 March 2020 1 9K Report

Is there a resource to find these properties?

Dear Kai Coldsnow, to my knowledge, both MoS2 and WS2 are insoluble in any organic solvents, including glycols. You can only obtain suspensions / dispersions depending on the particle size. Stable dispersions of the two metal disulfides have been obtained by coating the particles with polyethylene glycol or by using thioglycolic acid as reported in the article shown below.

Article Highly concentrated MoS2 nanosheets in water achieved by thi...

Badges
Science topic

More Kai Coldsnow's questions See All

Which remediation methods for groundwater and soil pollution lead to precipitation/dissolution ?

Nowadays, many remediation methods have been applied to the remediation of groundwater and soil, including physical, chemical, biological, in-situ and ex-situ. Which of these methods involves the...

22 April 2024 6,837 0 View

DNA isolation of Vitis root fungi?

Dear Team Fungi, We would like to identify root fungi from Vitis vinefera via metabarcoding. The methodology is established, we have had good results with other root samples using the isolation...

17 April 2024 5,406 2 View

SMARTPls Questions. Internal consistencies in SmartPLS and procedures in deleting indicators (loadings/weights). Why and how?

It is my first time using SMARTpls and I stumbled upon a few issues that my books/readings do not seem to answer. The below are the issues. Thank you in advance for the guidance and advice. The...

29 March 2024 4,593 0 View

Request for modeling?

use excel and figure out the solution

01 January 2024 4,945 1 View

Does anyone have access to this old Portuguese literature on zoology?

Dear friends, I am seeking the following Portuguese literature, which is on zoological systematics. Any suggestions would be greatly appreciated. Ferreira, J. Bethencourt. 1897. Sobre alguns...

20 December 2023 5,083 2 View

Can the arithmetic mean of microwave scattering data at different azimuth angles be regarded as multi-view processing?

I wish to perform yamaguchi decomposition on microwave scattering indoor measurement data, but yamaguchi decomposition requires multi-view data. Thus, can the arithmetic average of the observation...

14 October 2023 9,356 0 View

Stem cell embryoid body emtpy center?

Hi I'm using pluripotent stem cells to induce hematopoietic stem cells. We use APEL media containing 20ng/ml BMP4, 20ng/ml VEGF and 40ng/ml SCF. We seed around 10,000 cells/well in 96-well plate,...

22 July 2023 9,446 1 View

Factor score of dependent variable in JASP?

Hi all, I would really appreciate if someone can guide me how to obtain the factor score of dependent variable in JASP SEM analysis results.

20 July 2023 8,779 1 View

Does anyone know what is chemical structure of ALC-0307 lipid?

I tried to contact Acuitas Therapeutics regard their patented lipid ALC-0307 but heard nothing back. Some lipid supplier such Avanti also helped me to contact Acuitas but still didn't get any...

08 May 2023 3,606 0 View

Are you interested in less routine and time-consuming tasks - just load parameters and up to 200 samples for automated incubation and measurement ?

Bioscreen C° Pro provides a tightly controlled environment for measurement of growth of bacteria, molds, yeasts, or spores. For references please look at www.bioscreen.fi or ask back your question...

26 April 2023 2,616 0 View

How can we reduce the porosity of tungsten oxide (WO3) thin films during DC sputtering deposition (target: W, power: 100 W, 75 W, and 50 W)?

We are fabricating a tandem structure where a ~50 nm thick WO3 film is deposited between two metal films using DC sputtering. We use a mixture of Ar and O2 gases at different flow rates while...

01 July 2024 2,686 2 View

Can anyone suggest an adhesive that can sustain 600C?

I have to join tungsten wire to metallic plate with that adhesive and entire assembly has to be heated upto 600C in ultra high vacuum. I know about zirconia paste but it is not readily available...

18 June 2024 3,092 3 View

[SOLVED] Philips SEM XL30 (Tungsten Filament): HT not working after pressure failure?

Dear fellow researchers, We are currently operating a Philips XL30 Scanning Electron Microscope (SEM) equipped with a tungsten filament and have encountered a significant issue. Recently, our...

28 May 2024 232 2 View

[SOLVED] Philips SEM XL30 (Tungsten Filament): HT not working after pressure failure?

Dear fellow researchers, We are currently operating a Philips XL30 Scanning Electron Microscope (SEM) equipped with a tungsten filament and have encountered a significant issue. Recently, our...

28 May 2024 9,415 2 View

How to create a thin film of tungsten oxide nanoparticles on glass plate?

I've tried to prepare a thin film of tungsten oxide nanoparticles on glass plate with the help of following methods- 1. Nanoparticles were dispersed in Poly-ethylene glycol (PEG) and the...

16 May 2024 9,007 1 View

How to process CG simulation for protein containing disulfide bonds?

Hello, everyone I am simulating a single chain protein containing disulfide bonds. Force filed of Corase Grained simulation is Martini 2.2, it was run in gromacs2020 in Windows system. I wonder...

07 May 2024 4,213 2 View

Reason(s) for the difference in RMSD of the Docked Structure and Co-crystal?

Aside from defining the disulfide bond, what other reasons could account for the significant difference in RMSD of the docked structure and co-crystal?

15 April 2024 7,706 2 View

Need Help with Chip Formation Issue in 3D Turning Process?

Hello Members, I am facing an issue with chip formation in a 3D turning process simulation, and I would greatly appreciate any insights or suggestions on how to address this problem. I have...

02 April 2024 2,110 0 View

I want to make a 2D structure of molybdenum disulfide in material studio?

As in material studio every structure is in 3 dimensions. How will I change it into 2D like a 2D nanosheet. A graphene structure can be converted into 2D nanosheet, but when I tried this one by...

12 March 2024 7,245 0 View

Sentaurus TCAD - How can i simulate gidl currents?

Recently i started to learn 3D NAND in sentaurus TCAD, but there seems to be some problems in GIDL ERASE. 3D NAND uses BTBT for GIDL ERASE. To implement this, I would like to know what code...

25 February 2024 1,733 0 View