What are the sequenced steps of using linear programming in optimization landuse allocation, after defining the objective function & constraints?

More Rabab Ali's questions See All

Why Do TDS and EC Increase with Larger Wastewater Volumes, While BOD and COD Decrease?

I have carried out MFC experiments on three different volumes, 50, 500 and 1000 mL of wastewater. Results after MFC treatment shows that TDS and EC are more in larger volumes of water i.e. TDS and...

09 August 2024 9,621 0 View

How to enrich pig excreta for increasing nutrient quality organically ?

Pig slurry is rich in major and minor nutrients. Is there any way to improve / Enrich its manure quality to be used in agriculture organically ? please share your knowledge.

09 August 2024 5,605 2 View

Is it possible to plot the atom-projected band structure using GPAW?

Hi, I'm currently working on a project where I need to plot the atom-projected band structure using GPAW. I've been able to calculate the band structure for my material, but I'm having trouble...

07 August 2024 269 3 View

How can we differentiate between calcite, dolomite, siderite, magnesite and ankerite minerals in carbonatite rocks in thin section under op microscop?

How can we differentiate between calcite, dolomite, siderite, magnesite and ankerite minerals in carbonatite rocks in thin section under optical microscope?

07 August 2024 2,132 3 View

Unusual intensity drop in some sections of chromatograms in DDA?

Hi, we have measured tryptic peptides using both DDA and DIA method on QExactive. In DDA replicates i saw unusual intensity drops occurring at the same sections of chromatograms in DDA replicates...

07 August 2024 3,218 4 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

Leaf area of tomato ?

Hi How can this equation Ln(LA) = 1.038 + 0.89 ln(X) be applied to calculate the leaf area of a tomato? Can you explain with an example and what is the substitution of Ln and ln?

06 August 2024 2,508 2 View

Absorption coefficient of methane?

Hello, Can anyone provide me with the absorption coefficient of methane gas at 7.7 um? Any reference?

06 August 2024 980 5 View

Why did the authors extrapolate a phenotype that they experimentally proved in one bacterial strain across the whole genus of the organism?

I aim to be as skeptical as possible regarding whether a pair of orthologous genes results in the same phenotype in their different but related bacterial organisms under similar environmental...

05 August 2024 6,787 4 View

How to preform densitometry on SDS-page bands?

I ran a SDS-page of a bacterial lysate and I want to quantify protein concentration in a specific band. I was thinking of using a standards ladder or make some standards are different...

05 August 2024 9,805 3 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How much area/acres of agriculture land can irrigate by 1 cusec of water?

Kindly response

08 August 2024 1,214 2 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

What are the shear and normal stiffness values of an LLDPE liner in 3D numerical modeling of a stockpile?

I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...

05 August 2024 3,665 0 View

How to report results of Generalised Linear Mixed Models in a journal article?

Hi everyone, If you have written or come across any papers where Generalised Linear Mixed Models are used to examine intervention (e.g., in mental health) efficacy, could you please share the...

04 August 2024 4,130 4 View

Seyyid Ahmed Medjahed

Hi, after defining the objective function and constraints, we can solve the linear programming by using matlab optimization toolbox.

The command is : linprog

Hi,

If you have defined the final form of your objective function, you can easily solve the problem by using matlab, the command is "linprog"

Michael Patriksson

Here is a nice report in this area, in particular on the necessity to clearly specify what is needed or not - although it appears that some of the math is missing:

http://www.cresp.org/cresp1/cresp1/stewardship/Report31.pdf