What are the international Journals of wind turbine engineering of (impact fact less than 1.2)?

05 May 2014 1 9K Report

I work on testing a segmented HAWT blade of 7 m length. I want to submit my work to an international journal. Because I'm not an expert so I want a good journal but with suitable Impact Factor.

Nishant Kumar

Climate Modeling for Renewable Energy Applications,Hindawi Publishing Corporation, IF=1.2

Some other Journals:

Journal of Wind Engineering & Industrial Aerodynamics [elsevier, IF= 1.3]

Wind Energy, John Wiley & Sons, Ltd. , IF=1.4

Journal of Renewable and Sustainable Energy, IF=1.5

You can Go through this:

Best of luck

Badges
Science topic

More Ahmed H. Abdulaziz's questions See All

What is acceptable range of pressure in vacuum bagging resin infusion?

I need to know name of standards that provide allowed vaccum pressure in resin infusion.

02 March 2019 4,145 1 View

What are the best mesh quality criterion for inspection element quality?

I know about mesh density, skewness, wrap angles, and aspect ratio. Per literature, aspect ratio is a quick tool to define quality of mesh. Is there a rule of thumb for acceptable values of...

01 February 2019 2,623 5 View

How to determine the delamination critical stress in sandwich panel with laminates skins upper and bottom?

I study the delamination of laminates upper and bottom skins of honeycomb composite structure simple supported from two sides and under bending stress. I consider the developed tension on the...

01 February 2019 4,254 2 View

What is impact of elements overlapping on the accuracy of solutions?

In FE some elements are overlapping. I read a paper says thst such overlapping causes higher in plane stiffness only. I wonder does the impact on accuracy of solutions very big?

01 February 2019 10,022 7 View

What are the important features in acoustics emission signals?

I do some experiments in using AE method to detect events. I can plot a lot of figures such as hits, signal strength, waveform, counts, events so on. Which data shall I concentrate on? A little...

31 December 2018 6,787 10 View

How can I start implementing method of moving asymptotes?

I'm a little bit confused in regard of implementing MMA method. Should I transform the objective function into a Taylor series in order to use this method? Most of tutorials explain the...

31 December 2018 8,034 4 View

How can I get rid of elements overlapping in a knot for a finite element model??

I have developed a honeycomb sandwiched structure in Salome platform, meshed with netgen 2D, then calculated the compression stresses on it using Calculix open source FE. I tried to optimise the...

11 December 2018 1,075 1 View

What are the main considerations in injection mold designing and calculations?

I'd like to know the main parameters that should be considered in designing of injection mold. Also, I need to know a source for standardized calculations.

01 February 2018 755 4 View

How can I start learning Calculix coding?

I have a problem in understanding the coding of the Calculix examples. Is there any reference to help me understanding Calculix coding.

05 June 2017 7,937 2 View

What are the sources of error in using an APDL Ansys code on two different versions with two nonsense solutions?

We have a code for a benchmark problem. We used this code in Ansys 14 and in Ansys 17. However, we get two different nonsense solutions. Further, we repeated running the code on Ansys 14 and it...

03 April 2017 1,710 3 View

Which Scopus Journal provides the most affordable fees?

"PUBLISHING IN A SCOPUS JOURNAL" Researchers are now at a cross road. The critical need to publish in a Scopus or ISI, etc journal is ever vital. Journal Publication fees must be submitted....

10 August 2024 8,621 1 View

Geotechnical Engineering (Proceedings of the ICE) time review?

Hello everyone, I recently submitted an article to Geotechnical Engineering (Proceedings of the ICE), and the current status has been listed as "EiC Pre-assessment: Ready" for the past 20 days. I...

10 August 2024 6,493 1 View

Seeking Advice on Viability and Execution of Undergraduate Thesis Topic?

Hello everyone, I am currently developing a thesis proposal and would appreciate your input on its viability and how to effectively carry it out. My proposed topic is: "Does the perceived threat...

10 August 2024 8,992 0 View

How to develop investments in renewable energy sources?

08 August 2024 5,112 3 View

Who will be moral responsible for the death of thousands of people in the event of an earthquake?

Who will bear moral responsibility for the deaths of thousands of people in the event of an earthquake? Weeks and months remain before the onset of strong earthquakes that bring death to...

08 August 2024 6,134 12 View

Are there any instruments for studying time similar to the way it is in space?

There are a huge number of methods for studying objects in space, according to the senses (and not only). Mechanical, thermal, optical, acoustic, electrical, magnetic, based on particle beams,...

06 August 2024 7,102 0 View

Research Methodology - Impact of Corporate Reputation on Stakeholders Behaviors?

Please can anyone support with the survey questions based on RQ measures and propose how to do it in FMCG industry and include as well the role of brand equity Thanks

06 August 2024 949 0 View

Anyone having idea about VN primer for miRNA primer design ?

How to design VN primer to attach with universal reverse primer

05 August 2024 2,116 3 View

In the case of a wound l recurrence after radical breast cancer and sentinel lymph node biopsy. Are the sentinel lymph node procedure recommended?

In the case of a wound l recurrence after radical breast cancer and sentinel lymph node biopsy. Are the sentinel lymph node procedure recommended? If no axillary lymph node dissection was not...

05 August 2024 8,056 1 View

Regarding a model for simulating battery charge and discharge, what do you consider to be high fidelity?

Regarding a model for simulating battery charge and discharge, what do you consider to be high fidelity? What is the acceptable percentage of error (regardless of the metric)? Could you suggest...

03 August 2024 5,358 0 View