I need to know name of standards that provide allowed vaccum pressure in resin infusion.
For infusion, a vacuum about 0,8 to 0,9 bar is correct. It's possible to get down to 0,6 bar but verify before the compactation of the layer. It could be different.
I know about mesh density, skewness, wrap angles, and aspect ratio. Per literature, aspect ratio is a quick tool to define quality of mesh. Is there a rule of thumb for acceptable values of...
01 February 2019 2,623 5 View
I study the delamination of laminates upper and bottom skins of honeycomb composite structure simple supported from two sides and under bending stress. I consider the developed tension on the...
01 February 2019 4,254 2 View
In FE some elements are overlapping. I read a paper says thst such overlapping causes higher in plane stiffness only. I wonder does the impact on accuracy of solutions very big?
01 February 2019 10,022 7 View
I do some experiments in using AE method to detect events. I can plot a lot of figures such as hits, signal strength, waveform, counts, events so on. Which data shall I concentrate on? A little...
31 December 2018 6,787 10 View
I'm a little bit confused in regard of implementing MMA method. Should I transform the objective function into a Taylor series in order to use this method? Most of tutorials explain the...
31 December 2018 8,034 4 View
I have developed a honeycomb sandwiched structure in Salome platform, meshed with netgen 2D, then calculated the compression stresses on it using Calculix open source FE. I tried to optimise the...
11 December 2018 1,075 1 View
I'd like to know the main parameters that should be considered in designing of injection mold. Also, I need to know a source for standardized calculations.
01 February 2018 755 4 View
I have a problem in understanding the coding of the Calculix examples. Is there any reference to help me understanding Calculix coding.
05 June 2017 7,937 2 View
We have a code for a benchmark problem. We used this code in Ansys 14 and in Ansys 17. However, we get two different nonsense solutions. Further, we repeated running the code on Ansys 14 and it...
03 April 2017 1,710 3 View
Periodic structures can give outstanding mechanical/dynamical.
01 February 2017 4,322 3 View
"PUBLISHING IN A SCOPUS JOURNAL" Researchers are now at a cross road. The critical need to publish in a Scopus or ISI, etc journal is ever vital. Journal Publication fees must be submitted....
10 August 2024 8,621 1 View
How can I determine a good adhesion strength range for coatings on polymer surfaces, such as DLC on polymer substrates? Is there a specific threshold for adhesion strength (from T-peel tests)...
10 August 2024 942 3 View
Hello everyone, I am currently developing a thesis proposal and would appreciate your input on its viability and how to effectively carry it out. My proposed topic is: "Does the perceived threat...
10 August 2024 8,992 0 View
I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...
09 August 2024 5,048 2 View
Who will bear moral responsibility for the deaths of thousands of people in the event of an earthquake? Weeks and months remain before the onset of strong earthquakes that bring death to...
08 August 2024 6,134 12 View
I did PR spin coating on trench structure. I used AZ P4620 PR and the thickness or PR is around 11um. The substrate is Si. And my trench structure depth is 141um(negative way). Even though I...
08 August 2024 2,298 0 View
I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...
07 August 2024 1,028 0 View
I have been getting a low plasma and no coating while doing rf sputtering of copper doped ZnS using a power of 140 watts and at pressure of 6.5x10-3 Mb.
07 August 2024 4,526 4 View
The first pdf file I uploaded had an error. So I uploaded an updated, corrected pdf of that paper with a different pdf name. I dpon't want the old copy to be download or read.
07 August 2024 9,508 1 View
Hi! So i attempted to understand a novel protein behavior towards heat application by analyzing its secondary structure change. I subjected the protein to a thermal denaturation analysis using...
06 August 2024 1,989 3 View