Despite single-cell RNA, how can I characterize a new cell subtype/phenotype?

A new cell subtype was found out only during regeneration phases after a cuprizone-induced demyelination model. How can I characterize this cell? It is important to highlight that was already...

13 February 2021 1,245 1 View

Permanent Fluid temperature initialization in Ansys Fluent?

Dear researchers, I am coupling Design Optimization with ANSYS Fluent in Workbench 2020 R2. I can do the analysis. I am patching the initial Temperature values of the zones. However, the patch...

28 January 2021 4,265 2 View

Luciferase assay for miRNA-gene: How to obtain DNA (PCR product) from the mutated primer?

To perform the Luciferase assay for microRNA-gene interaction its necessary a primer (wild-type) to amplificate the specific ligation site and also a mutated primer. But if your primer has a...

19 January 2021 8,568 3 View

How to couple Moldex 3D with MATLAB for design optimization of an injection mould?

Hello, I would like to use the software Moldex 3D for the design optimization of an injection mould. How can I couple Moldex 3D with a MATLAB code? Any help appreciated, I wish you all a happy...

09 January 2021 569 2 View

How to setup ANSYS Fluent for simulating the filling stage of an injection mould?

Hello, I am using ANSYS Fluent for simulating the filling stage of an injection mould. However, when comparing the results with those of specialized software, such as Moldex 3D, I found the...

07 January 2021 7,992 1 View

Which plants and trees have the best ability to prevent the entry of particulate matter (PM2.5 and PM1) and nanoparticles in indoor environments ?

In recent years our group has highlighted the importance of trees and plants in public and recreation parks in large mega cities. However, we are interested in developing "green shields" to be...

05 January 2021 6,500 3 View

How to phosphorylate specific residues on pymol?

Hi everyone, I am using the pyTMs plug in on Pymol to phosphorylate a particular threonine in my protein. I am having difficulty in selecting only one or two residues - it seems I can only...

05 January 2021 230 3 View

How to perform Potential Surface Energy Exploration (PES) calculations?

I would like to receive help, as I am trying to make an analysis of the ethanol PES, but the calculations are always giving error. I use the conda-forge version of xtb (* xtb version 6.3.2...

04 January 2021 602 2 View

How do you create a funnel plot in STATA to assess publication bias using proportions from the metaprop command (for a meta-analysis)??

Hi everyone! I am trying to use STATA to create a funnel plot to asses publication bias using proportions from studies for a large meta-analysis (having used the metaprop command). I"m having...

09 December 2020 6,096 3 View

How to get the model shape matrix from Nastran?

I need to include the bending mode dynamics in my simulation. So far, I am only considering the rigid body dynamics. So I need to implement the following equation: q'' + Kg*q = Phi*F(t), where:...

19 November 2020 4,270 5 View

Is There Any Feasible Method To Test Fluorescent Compounds Other Than Fluorescence Spectrometers ??

Is There Any Feasible Method To Test The Efficiency Of Fluorescent Compounds Other Than UV Spectrometers ? Suggestions Would Be Appreciated !

02 March 2021 5,785 3 View

What is Flat Lens Antenna?

28 February 2021 5,433 3 View

Can impedance of antenna be less than 50 ohms?

I am simulating helix antenna in hfss, right now, giving excitation with 50 ohms port. When I see the results of Z parameter (real). It shows lower than 50 ohms. Do not understand, if it can be...

27 February 2021 4,218 7 View

Could the "incoming radiation (net radiation)" values be negative?

Could the "incoming solar radiation" values be negative? What is the difference between "global solar radiation" and "incoming solar radiation"? Which one might be measured negative values?

21 February 2021 7,726 9 View

In methylene blue test Why is UV absorbance reading very low as soon adsorbent is added and then increasing before reaching equilibrium?

Hello, I'm working on removal of methylene blue. 01. in the dark test very first reading is taken 15 minutes after adding adsorbent to the dye solution and that UV absorbance reading is very...

19 February 2021 472 5 View

If the electron is a wave, then what is its nature? Is it an electromagnetic wave?

If the electron is a wave, then what is its nature? Is it an electromagnetic wave? Thank you very much,

17 February 2021 9,024 4 View

How to perform Cox proportional hazard analysis or Kaplan-meier survival analysis in SPSS?

At first please see the attachment. This experiment was performed for a period of 7 days (n=100). After 7 days, we found different level of survival rate (%) for each treatment. Now, I want to...

15 February 2021 9,145 2 View

How to calculate ultraviolet dose in Gy or J/kg?

Currently I'm doing a literature review regarding the comparisons of different types of radiation such as uv, electron beam and gamma radiation. But I'm having a difficult time converting uv unit...

11 February 2021 7,642 3 View

How to model in HFSS or FEKO Free Space Material Characterization?

I am having trouble setting up this problem in HFSS or FEKO. In HFSS, I've tried both FEM and FEBI-IE solvers. With FEKO, I've tried it's MoM solver and default settings. I am would like model...

09 February 2021 375 2 View

Distribution of modes fields ?

Hi, We find a specific distribution of electric fields in structure for different frequencies which can be seen using em solvers and known as modes. I would like to know how we can choose the...

04 February 2021 10,043 3 View