What are some secondary N-methyl amines having good Raman cross-section?

28 July 2016 0 9K Report

I would like to do Femtosecond Stimulated Raman Spectroscopy (FSRS) on the substrate to track the dynamics of N-H bond cleavage.

Badges
Science topic

More Nita Ghosh's questions See All

Z-average size from Dynamic Light scattering can it be lower than the original probe size?

Hi everyone, Recently I have been conducting Dynamic Light scattering experiments in a micellar solution at 5 and gel at 37 degrees of Celsius with latex particles of diameter 190-500 nm. While...

01 August 2024 1,168 4 View

GSH estimation assay: What is the right choice of standard?

Hi there, My question is: What standard curves should be used while estimating Tot GSH and GSSG by kinetic method using GR enzyme mediated recyling with DTNB chromophore? Actually I am following...

01 August 2024 8,217 1 View

Intracerebroventricular (ICV) AAV inj.?

I'd like to know if anyone has got experience in intracerebroventricular (ICV) AAV inj. I am looking for a concomitant spread of the AAV including but not limited to the motor cortex and the...

12 July 2024 781 0 View

What is the maximum acceptable degradation of gain in the orthogonal plane relative to the beam scanning plane for beam steering antennas?

In research papers on beam steering antennas, while the radiation pattern for the beam scanning plane (such as the horizontal or vertical plane) is typically presented, details regarding the...

03 July 2024 8,321 0 View

What kind of surface morphology must be there for good photocatalytic activity of thin film?

If I want to increase the photocatalytic activity of a thin film sample what should be it's ideal surface morphology and parameters? All scientific answers related this are highly appreciated.

19 June 2024 6,744 0 View

Why I am getting follwing error when I tried to open .dta file in SPSS25?

>Error # 7202. Command name: GET STATA >Input dictionary read error. >Execution of this command stops. Cross Product Matrices are not supported

19 June 2024 5,423 0 View

Which deposition technique is better (Spin Coating/Dip Coating) for making Ni doped ZnO thin film for better photocatalytic activity?

If I want to improve the photocatalytic activity of Ni doped ZnO thin film then which would be the better deposition process for thin film Spin Coating or Dip Coating?

18 June 2024 7,678 2 View

What are the possible parameters needed to be tuned for better photocatalytic activity of thin film?

If I want to enhance the photocatalytic activity of Ni doped ZnO thin film. For this what are the parameters I need to tune and how? Related this all scientific answers/explanations are highly...

16 June 2024 4,533 1 View

Curing of Novolak resin with hexamine develops yellow color. I believe it is due to azo linkage -C-N=N- C- What is the reaction mechanism?

Also, I will appreciate whole curing mechanism of Novolak with Hexamine

14 June 2024 9,908 0 View

How are cancerous cell lines generated in 1900s sold today have the same genetic profile?

From the definition of cell line, they are indefinitely propagated/subcultured. However, in practice beyond a certain passage number, they are said to loose characteristic gene profile, for e.g....

10 June 2024 6,890 1 View

Using OBD technique i am trying to measure laser induced shockwaves velocity i found that at start velocity increases and then decay?

i am unable to interpret why its increases in start as shown in figure

11 August 2024 2,179 1 View

Hello researchers Is this a random laser or just fluorescence?

I am using Rhodamine6G as gain medium and silver nanoparticles as scatterers on a microscope slide and laser input 532 nm comes from above.

09 August 2024 9,894 2 View

Why might the impedance values for DI water and 0.1X PBS buffer solution exhibit a decreasing and increasing trend, respectively over time (HP 4194A)?

Hello everyone, I'm encountering an issue with my electrochemical impedance spectroscopy (EIS) measurements and would appreciate some insights. Experimental Setup: Electrodes: Gold interdigitated...

05 August 2024 3,783 2 View

Could dyes amplify the spectrum of light to a specific wavelength?

I am interested to know the behavior of dyes toward light. Specifically, Blue dyes re-emit the spectrum, especially from the green zone (known as principal in LED lamps, and blue dyes are known...

05 August 2024 3,290 1 View

Conjugation of PEG-Amine to an Amino Acid Using EDC?

I am attempting to conjugate PEG to an amino acid at the C-terminus, for the purposes of producing nanoparticles. I have been told that PEG modified with amine groups can be used for this purpose,...

31 July 2024 2,033 1 View

Mossbauer spectroscopy Co0.6Mn0.4Fe2O4 MNPs?

Following curve related to Co0.6Mn0.4Fe2O4 Magnetic nanoparticles with extra phase a-Fe2O3. I will appreciate to help me to interpretation this spectroscopy, especially the blue line.

31 July 2024 9,140 2 View

Why do some of my Raman spectra show no signal at lower Raman shifts?

I'm using a InVia Renishaw Raman microscope system (785nm wavelength, 600l/mm grating density) to acquire Raman images on human brain samples, at 50um resolution. The samples are placed on MgF2...

30 July 2024 8,771 3 View

How to calculate conductivity using Electrochemical Impedance Spectroscopy's Nyquist plot?

Hello everyone, I am new to this characterization but watching videos on youtube I have already plotted a Nyquist plot (Z' and -Z'') and already fitted models on my material using Zsim. But now I...

29 July 2024 1,376 0 View

I have synthesized a composite of ZnO and In2O3 with variations in ZnO content. In Raman , what is the peak observed at 130 cm-1?

Dear all, I have noticed, as the ZnO content increases, the Raman intensity at 100cm-1 also increases. However, there is a peak nearby at 130 cm-1, which I could not find in any paper related to...

28 July 2024 5,410 1 View

How should operational parameters be selected when developing a pore-free laser welding technology?

There are three operating parameters - the laser power, the diameter of the focus spot and the scanning speed. It is necessary to obtain a seam of a given depth without pores. What parameter...

27 July 2024 7,168 2 View