Unable to Link "Mechanical Solution Cell" to "mechanical Model Cell" ANSYS ?

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

No title

02 March 2021 3,060 3 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

What is the characteristic length to determine the Reynolds number for the scattered turbulent fluid flow?

Dear all, I just saw this example in FB on the difference between laminar flow and turbulent flow. The flow from a pipe hits the sink and scattered. The flow from the pipe is characterized as...

02 March 2021 1,999 5 View

LOAD DISPLACEMENT CURVES Stiffness increasing in ANSYS non linear analysis. HOW CAN I CORRECT IT?

Hi. I am doing non linear FE analysis using a new material beam under flexural 2 point loading using ANSYS. I have defined a bilinear material model. The solution has converged. In results I am...

01 March 2021 9,911 3 View

Issues with Permeabilization during Flow Cytometry?

Hello Everyone. Currently I am working to characterize macrophages in the myocardium after ischemia-reperfusion injury in rats. Due to the low total cell number isolated from rat hearts I can...

01 March 2021 3,867 3 View

How to show arrows over the streamlines in CFD-post?

I follow this to make streamlines like the photos attached below: (software- CFD post-processing) First I plot the 2D streamline over a surface "streamline 1". them I plot a vector by the...

01 March 2021 8,668 3 View

Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS?

I need to model masonry and reinforced concrete minarets for my MSc thesis. Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS? (Or any other program for just...

01 March 2021 736 3 View

Which cell line should we use to perform biological dosimetry experiments?

We are preparing some experiments based on irradiating cells under different conditions in order to evaluate the effects in terms of DNA damage, genetic expression, etc. As our project is...

01 March 2021 3,355 3 View

Is it possible for two human neuronal cell lines to have different gene sequence for the same protein?

I am looking at the ATP1A2 (Sodium/Potassium ATPase alpha subunit 2) in two human neuronal cell lines. Expression levels of this protein seems to be almost equal when detected by one antibody....

01 March 2021 3,607 3 View

Mohammad Reza Bayat

Can you please explain more about your problem?

By the way, check the "Future analysis" in the "Analysis Settings">"Analysis Data Management".

Also if you connect the cells before solving the problem, ANSYS will automatically enable this option.

Vishnu Ganesh

Hi Thanks for for answer. I will expaln the problem in detail.

I am trying to model a composite material (Shape memory alloy and Aluminum) in ANSYS. This is a two step process i.e firstly a thermal cooling takes place where the temperature drops from 450 oC to 25 oC and then in the second step a small portion of this material is removed from the whole geometry. So because of the different thermal expansion coefficient of Aluminum and shape memory alloy, residual stresses are induced during the thermal cooling process. In the next step, when some of the material is cut from the whole Geomtry these residual stresses would be released to some extent. If you would look at the attched image i have sent you with this Email, I need to output the INISTATE Stress file from the first step, "Thermal Cooling" and input this file in the second step, "Material Removal". Now the problem is, I am unable to connect the "Solution Cell" from the first stage to the "Model Cell" in the second stage. I have also read the ANSYS documentation and this should be possible.