Titanium(IV) 2-ethylhexyloxide hydrolyzed in water?

Bushra Mughal @Bushra-Mughal-5

05 September 2023 0 9K Report

what is the effect of carbon chain on hydrolysis of titanium alkoxide in water?

Badges
Science topic

More Bushra Mughal's questions See All

Absorption coefficient of methane?

Hello, Can anyone provide me with the absorption coefficient of methane gas at 7.7 um? Any reference?

06 August 2024 980 5 View

How are Large Models Exploring and Outputting Knowledge Understanding in Specific Content Areas, and What Does Academic Research Say About It?

Hello everyone！ I am currently exploring the performance of large models in understanding knowledge in specific domains, and attempting to construct a knowledge framework similar to what...

05 August 2024 5,729 2 View

Regarding a model for simulating battery charge and discharge, what do you consider to be high fidelity?

Regarding a model for simulating battery charge and discharge, what do you consider to be high fidelity? What is the acceptable percentage of error (regardless of the metric)? Could you suggest...

03 August 2024 5,358 0 View

How do i get an account to upload my published papers?

need to open an account to upload my published papers

01 August 2024 9,255 1 View

What is the problem with these tissue culture plants?

All plants are green but some of these plants becomes yellow. I did not found any reason. Please help me to find out the real problem.

01 August 2024 589 4 View

How to correctly use the UTE and ZTE pulse sequences in Bruker's ParaVision software?

I am using a Bruker 600M solid-state NMR spectrometer with a Micro 2.5 microimaging system. The test sample is a tube of 1M LiCl aqueous solution, and the nucleus detected is 1H. I am trying to...

01 August 2024 9,227 1 View

Is artifacts in XPS possible to build high deviation in binding energy larger than 5 eV??

Hello. Thanks for your consideration to see my question. Recently, I conducted XPS anaylsis of g-CN that is prepared from thermal polycondensation of DCDA, so-called conventional bulk-g-CN,...

30 July 2024 9,824 2 View

Which statistical test should we use?

N=6 Comparing pre and post test likert scale responses. Participants are mix of practicing & preservice teachers.

30 July 2024 7,233 4 View

How to build my own lab made four point probe set up?

Hello, I'm trying to measure the conductivity of semiconductor films but since I don't have a commercial four point probe set up I would like to build one on my own in my lab. I have generators,...

30 July 2024 906 2 View

Can the limit of quantification (LOQ) of an analytical method fall outside its linear dynamic range, or must it always be within it?

Can an analytical method's limit of quantification (LOQ) be outside its linear dynamic range, or is it always required to be within it? Please provide a thorough explanation supported by verified...

29 July 2024 7,198 9 View

Hello, regarding Mxene 2D titanium carbide?

I fabricated Ti3C2Tx using concentrated HF 40%, I plot an XRD as attached image below.. please let to know if I obtained it or not.

02 August 2024 6,789 4 View

Ti6Al4V - Phase differentiation between alpha and alpha prime martensite?

Dear Researchers, Is it feasible to distinguish between alpha and alpha prime martensite in the Ti6Al4V alloy under rapid solidification in the as-cast state using XRD, in addition to...

30 July 2024 3,849 0 View

Could Nd doping into TiO2(anatse) because Nd's dense diameters are bigger than in TiO2 ?

could Nd (Neodimyum) doping into TiO2 because Nd's dense diameters are bigger than in TiO2

11 July 2024 2,350 2 View

Determine pore diameter by BJH of TiO2?

Dear all, l need to help me to determine pore diameter. I got from BJH data the rp(peak area), Desorption Isotherm was 1.6 nm, but from Isotherm l got type lV with hysteresis H2 loop. Can l used...

10 July 2024 2,872 1 View

What is the fastest method should i use to determine TiO2 content for thermoplastic without using any high tech instrument?

I currently conduct a hotmelt thermoplastic. I want to find the tio2 content in the product. As far as I know, titration method can be used since it is available for me. May I know what is the...

07 July 2024 5,264 3 View

Why are there holes on the surface of TiO2 films deposited by ion beam sputtering?

We have observed many holes on the surface of TiO2. These holes have a diameter of approximately 1 µm and a depth of about 30 nm. The formation of these holes is mainly related to the...

20 June 2024 3,861 1 View

How to weight this chemicals to mix up to make zeolite 13X-Tio2 with Fe doped?

I use molecular sieve 13X and Iron nitrate powder Fe(NO 3)3 • 9H2O. and commercial TiO2. I need to prepare 8% Fe, 8% TiO2 containing with zeolite 13X. I want to use this method below: WET...

17 June 2024 4,153 2 View

I am trying to simulate sputtering from a cylindrical target using RSD software. Can anyone help in creating racetrack for cylindrical target?

The target type is titanium; the height is 900 mm, the width is 70 mm, the race track height is 750 mm and the width is 50 mm.

04 June 2024 1,025 1 View

The pressure drop of porous media keeps increasing, why?

Hi y'all, I was trying to meausre the pressure drop under a constant flow rate. For the porous media like titanium fiber felt and sintered titanium, when I use deionized water OR alcohol,the...

02 June 2024 2,951 2 View

How to predict the mechanical properties like tensile stress of alpha + beta Titanium alloys by their grain mophology?

I don't know how to use the Hall-Patch equation for Titanium alloys that contain two phases.

29 May 2024 3,664 1 View