I am trying to simulate sputtering from a cylindrical target using RSD software. Can anyone help in creating racetrack for cylindrical target?

Sivakumar Periyasamy @Sivakumar-Periyasamy-7

05 June 2024 1 1K Report

The target type is titanium; the height is 900 mm, the width is 70 mm, the race track height is 750 mm and the width is 50 mm.

Koen Strijckmans

Please check the documentation of the RSD software on

https://www.ugent.be/we/solidstatesciences/draft/en/services/software#RSD

But I added also in attachment.

The info you look for should be on page 40 of the RSD manual.

Good luck!

Badges
Science topic

More Sivakumar Periyasamy's questions See All

Seeking Advice on Viability and Execution of Undergraduate Thesis Topic?

Hello everyone, I am currently developing a thesis proposal and would appreciate your input on its viability and how to effectively carry it out. My proposed topic is: "Does the perceived threat...

10 August 2024 8,992 0 View

To perform transfection with DharmaFECT Duo in AGS cells. Could you tell me what the ideal concentration is to avoid significant cytotoxicity?

I would like to perform transfection with the reagent DharmaFECT Duo (Horizon) on the AGS cell line. Could you please inform me of the optimal concentration to use without causing cytotoxicity in...

03 August 2024 3,851 1 View

What is meant by baseline of FTIR data?

I got comment on my FTIR data figure from a reviewer. The reviewer said "FTIR data in Figure should be repeated. there is no bassline." I made Y off set comparison graph of FTIR on OriginLab. Can...

03 August 2024 6,070 3 View

What is Random Audit?

HI there, I've came across several articles discuss about random audit an Non random to tax evasion or compliance. Most of the articles is relating about effect of audit (random or non random)...

31 July 2024 5,309 7 View

Is the mentioned CV graph a valid one as this graph have only one peak prominent (reduction)?

I have used Prussian blue nanoparticles as a redox couple. The PBNPs have been made using only one salt precursor. Also, during scan rate studies, a small oxidation peak can be consistently found...

31 July 2024 9,697 0 View

How we can use lattice-based cryptography for construction of S boxes?

Please suggest basic literature on lattice-based cryptography. A kind response from the cryptographic community will be highly appreciated.

24 July 2024 6,291 4 View

I am working on III-V based tandem solar cells.Can anyone explain that solar cells work under forward or reverse biased conditions?

I want to know that n-doped side of solar cell is connected with positive or negative electrode.

20 July 2024 1,348 2 View

Can it is possible to find the cleaved sequence when a protein cleaved by a heamaglutanin protease (HA/P) by any bioinformatics tools?

Bioinformatics tools like peptide cutter

15 July 2024 6,453 1 View

Hello, does anyone know how I can get coordinates of two specific points on a moving body in Abaqus when applying a vdload subroutine?

Hello I am trying to simulate repulsive force of two permanent magnets in Abaqus. I have implemented Force equations into a vdload subroutine. sensitive parameters are the center to center...

15 July 2024 3,491 0 View

FACS markers to characterize rat bone marrow-derived macrophages?

Dear all, I am looking for FACS markers to characterize my rat bone marrow-derived macrophages (M0). They were differentiated from monocytes with M-CSF. I am considering to use CD11b/c and...

15 July 2024 4,615 1 View

Why do i have a weak plasma and no coating during rf sputtering?

I have been getting a low plasma and no coating while doing rf sputtering of copper doped ZnS using a power of 140 watts and at pressure of 6.5x10-3 Mb.

07 August 2024 4,526 4 View

Hello, regarding Mxene 2D titanium carbide?

I fabricated Ti3C2Tx using concentrated HF 40%, I plot an XRD as attached image below.. please let to know if I obtained it or not.

02 August 2024 6,789 4 View

When I simulate for S parameters using ADS, I have faced this issue that I have attached. Please anyone clarify me?

...

31 July 2024 1,671 3 View

Ti6Al4V - Phase differentiation between alpha and alpha prime martensite?

Dear Researchers, Is it feasible to distinguish between alpha and alpha prime martensite in the Ti6Al4V alloy under rapid solidification in the as-cast state using XRD, in addition to...

30 July 2024 3,849 0 View

Wrong out put for gmx x2top?

Dear users, I would like to simulate a zeolite structure in gromacs. I got the .cif file from IZA expanded in one direction in Materials Studio and exported a .pdb file. However, when I want to...

24 July 2024 367 4 View

How to scrape off the surface layer of compound sputtering targets as with multiple usage top layer's stoichiometry changes from the original target?

I am experiencing this for the Bi2Se3 sputtering target. Initially, even if the target was 2:3 in Bi : Se, with a few sputtering runs, due to the high escaping tendency of selenium, the top layer...

23 July 2024 1,649 1 View

Optimal condition for depositing FTO target 95:5% using sputter technique?

Hello I want to know about the sputtering condition of depositing FTO from target 95:5%. I tried with RF sputter in pressure 2.5Pa and 100 sccm Ar at room temperature but it showing no...

21 July 2024 1,680 2 View

Trial exclusion in eye-tracking data?

Is it reasonable to exclude all trials with a blink or saccade in the 150 ms before stimulus onset? As an alternative, would it be better to exclude blinks (after extending them by about 100 ms...

19 July 2024 3,838 0 View

Can a private laptop with 16GB RAM and Intel i5-1235U 1.3 GHz processor be used for WRF simulation with a 12*12 km domain?

I want to simulate WRF for a 12*12 km domain size. I want to run LSM and BSM models with a 5 minutes time interval. My laptop specification is 16GB RAM and Intel i5-1235U 1.3 GHz processor. Can I...

13 July 2024 2,037 0 View

Could Nd doping into TiO2(anatse) because Nd's dense diameters are bigger than in TiO2 ?

could Nd (Neodimyum) doping into TiO2 because Nd's dense diameters are bigger than in TiO2

11 July 2024 2,350 2 View