Suggest an idea about contact in Ansys Workbench?

09 September 2016 0 403 Report

I'm model a pullout specimen in static structural (ANSYS WORKBENCH) used a contact tool was bonded . After analysis it showing the result in concrete only and not in rebar (steel reinforcement)

Badges
Science topic

More Thennavan M's questions See All

Can anyone give an idea about the latest research topic in Structural Engineering field ?

11 December 2018 4,594 4 View

How to give surface to surface Cohesive interaction in abaqus Explicit analysis?

how can I use Cohesive behavior, damage initiation and damage evolution??. surface based cohesion behaviour cannot supported in explict analysis?

03 April 2017 3,759 2 View

Pullout test in RCC getting an Error in Abaqus Explict analysis?

I Used a zero thickness cohesive element between a rebar and concrete. CDP, cohesive materials properties(damage for traction seperation laws) are used in the analysis and displacement control...

02 March 2017 10,607 2 View

How can I show crack pattern due to pullout test in abaqus?

Hi everyone. I have a problem to model concrete crack in abaqus.I use Concrete Damaged Plasticity (CDP) in my model, I can run my model but I can not show the crack pattern.I read one paper, and...

01 February 2017 3,233 3 View

Suggest an Idea about the RC tensile crack propagation in Abaqus?

i need to show the cracks in reinforced concrete due to direct tension test. Is it possible in abaqus?

31 December 2016 7,297 4 View

How to choose a element for concrete & Rebar in Abaqus?

how to choose a element for concrete & Rebar in Abaqus?

10 November 2016 7,415 0 View

How to apply a force on nodes( in abaqus software)?

It is difficult to apply a force on nodes ? anyone give an idea...

10 November 2016 9,105 8 View

Is there any option to view cracks in ansys workbench?

Is it possible to view the cracks in Ansys Workbench?

10 November 2016 5,270 2 View

Is there any step by step procedure for FE modelling of tension stiffening Prism?

Is there any step by step procedure for FE modelling of tension stiffening Prism in Ansys software ?

09 October 2016 9,396 0 View

Can anyone give an idea about tension stiffening effect?

1.How the tension stiffening mechanism will work ? 2. define tension stiffening ? and tension stiffening effects?

09 October 2016 5,643 1 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

How to fix errors in my heat transfer steel structure with reinforced concrete slab model Abaqus?

I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...

07 August 2024 1,028 0 View

Can anyone explain why there is not any color bands in the middle portion of the tensile coupon?

Details of the Analysis. Static Analysis Composite Layup Continuum Shell Elements FRP Material (Elastic and Hashin Damage)

03 August 2024 8,538 4 View

What are the limitations and challenges of using machine learning for predicting concrete compressive strength in practical applications?

Machine learning (ML) has shown great potential in predicting the compressive strength of concrete, an important property for structural engineering. However, its practical application comes with...

03 August 2024 2,546 2 View

What should be the sample container for the hydrothermal reaction in a microwave reactor at 180 °C for 10 min at the heating rate of 5 °C per minute?

Suggest one of them 1. Teflon-lined stainless steel autoclave: 2. Alumina (Al2O3) ceramic container

30 July 2024 7,326 1 View

Tangential stiffness option in ansys workbench?

I am not able to find how I can provide tangential stiffness in ansys workbench The normal stiffness option is there. But how I can enter tangential stiffness I have read somewhere tangential...

29 July 2024 2,032 2 View

How to Import Blade geometry from CAD file in ANSYS design modeler?

Hello. I have the geometry of a blade in CAD file (stp) and I want to prepare the blade for meshing with turboGrid. I must import this file into designModeler and then transfer to the...

27 July 2024 356 3 View

Will the catalytic effect of retained austenite happens in steels including RA?

The catalytic effect of retained austenite refers to the phenomenon wherein quenching steels with a small amount of retained austenite, when subjected to tempering at a specific temperature...

27 July 2024 8,508 0 View

Why might I be observing hysteresis in my stress-strain curves when using the Mohr-Coulomb model, despite not applying dynamic loading?

While working on caisson foundation, I applied static vertical load

25 July 2024 9,357 1 View