Some questions about the plane strain and plane stress state?

11 November 2016 0 7K Report

in the plain strain state definition, the Z-direction has stress ,but no strain. is it possible a direction have stress but no strain?

likewise, for the plane stress state, there has strain ,but no stress,is it possible?

Badges
Science topic

More Hou Wang's questions See All

Why austempered can have higher toughness than quenched and tempered in steel?

Why austempered can have higher toughness than quenched and tempered in steel , though both have same hardness? (ASM Metals Handbook,Vol. 4 ). Thank you.

06 July 2017 340 0 View

What’s the fatigue propagation mechanism of ductile and brittle steel ,from the view of physical metallurgy？

What’s the fatigue propagation mechanism of ductile and brittle steel ,from the view of physical metallurgy？ Thank you very much.

04 May 2017 7,313 2 View

What's physical meaning of fatigue endurance limit?

what's physical meaning of fatigue endurance limit? how to calculate or estimate fatigue crack initiation life?

11 December 2016 7,632 0 View

What kinds of characteristics those fracture surfaces have?

low-alloy steel(0.4C-1.4Cr-1.0Al-0.35Mo) ,carbonitriding at 860℃ about 4 hours,quenching and 190℃ tempering .carbon potential and nitrogen potential are 0.75 and 0.2 respectively. Enclosed file...

09 October 2016 6,999 0 View

What’s the Griffith crack length in high-carbon martensite or plate martensite?

What’s the Griffith crack length in high-carbon martensite or plate martensite?In quench martensite ,there is no carbide which need tempering to produce carbide precipitation, then what’s the...

09 October 2016 6,886 2 View

What effects temper martensite embrittlement have on fatigue of steel ?

what effects temper martensite embrittlement have on fatigue crack nucleation and propagation?

09 October 2016 10,087 26 View

How can calculate fracture load of three-point bending testing through strength and ductility data obtained from tensile testing?

How can calculate fracture load of three-point bending testing through strength and ductility data obtained from tensile testing? and in three-point bending testing ,how to calculate stress...

08 September 2016 6,682 4 View

Will the crack shape and crack tip radius affect KⅠc value and R-Curve?

Will the crack shape and crack tip radius affect KⅠc value and R-Curve? and why ? Thank you for your answers.

08 September 2016 524 53 View

Is it possible the cleavage fracture happens after large amount of elongation in the uniaxial tension test of intact sample?

In some steels,is it possible the cleavage fracture happens after large amount of elongation in the uniaxial tension test of intact sample?

07 August 2016 8,407 9 View

What’s the micro-mechanism process of cleavage in uniaxial tension test of intact steel sample?

What’s the micro-mechanism of cleavage in uniaxial tension test of intact steel sample?→the microcrack forms when the tensile stress exceed cleavage stress, then propagate immediately.Or:→the...

07 August 2016 3,920 0 View

How to learn more about SPSS and its Application?

I would like to learn more about SPSS and Its application especially in regards to data analysis. Please suggest me how I can learn more about it. Thank you so much.

11 August 2024 9,101 4 View

Can I base on reverse DNA sequences to perform alignment, convert to amino acids and GenBank submission?

I have reverse sequences (AB1 format), can I base on reverse DNA sequences to perform nucleotide alignment, convert nucleotides to amino acids and deposit the sequence in GenBank database?

11 August 2024 5,138 1 View

Baseline drift in HPLC? What causes this?

Hello, Why do i see this baseline drift when i compare my blank (black) to the sample (blue)? Any suggestions as to why this happened? Thank you!

11 August 2024 3,770 4 View

Text-Communication from the M1 Hand Area using BCI—and then there is Elon Musk?

Willett, Shenoy et al. (2021) have developed a brain computer interface (BCI) that used neural signal collected from the hand area of the motor cortex (area M1) of a paralyzed patient. The...

10 August 2024 7,180 0 View

Has anyone applied Python in the field of textile engineering for data analysis, automation, or smart textiles?

I'm currently exploring the application of Python in textile engineering, specifically in areas like data analysis, process automation, and the development of smart textiles. I'm interested in...

10 August 2024 7,429 2 View

How can I use the cif data obtained from rietveld refinement extracted via gsas2, for microstructural analysis using ETEX software?

09 August 2024 7,718 0 View

How are iso-frequency contours plotted?

Let's say we have a standard, regular hexagonal honeycomb with a 3-arm primitive unit cell (something like the figure attached; the figure is only representative and not drawn to scale). The...

07 August 2024 1,937 1 View

Stability of the Solar System: Insights from Einstein’s Equations ?

The stability of the Solar System is a complex subject that blends the classical framework of Newtonian mechanics with the modern insights provided by General Relativity (GR). Understanding this...

07 August 2024 2,569 1 View

How to prepare the nanoparticle treated fungal sample for Environmental SEM analysis?

A fungal strain was treated with nanoparticles. We want to do an environmental SEM analysis. So could anyone share your views on preparing the sample? Thank you.

07 August 2024 5,307 1 View

How to normalize and take the significance of the MTT OD values with 3 replicates for the same cell-line?

Hi, I have a question about normalizing the MTT OD values for doing the statistical analysis. So, if we have 3 different plates and we call them 3 different replicates, so, first we would...

07 August 2024 8,106 4 View