I am trying to use Ieee802.15.4narrow as a base for my simulation. I want to get the RSSI value, but I don know how to print the RSSI when a packet is received in a node.
I am relatively new in Omnet++ and I am wondering if anyone could help me.
Hi Ameneh:
Can you please guide me for calculating RSSI?
Hi Ameneh, i'm trying to calculate the RSSI in the same base simulation too, can you solve it?
I need an article titled Mindfulness Based Reality Therapy by Julian Pierce for research.
11 May 2024 1,964 3 View
We started to produce our in house screen printed electrode. I want to check reproducibility in a single batch and batch to batch variation. I did CV and considered the first cycle and measured...
04 December 2023 8,737 2 View
I am trying to deposit PB on carbon electrodes. I tried electrochemical deposition. I couldn't deposit any thing, I did chemical synthesis and dropcasting on the surface of the electrode. looks...
04 December 2023 7,445 2 View
Hello everyone It is a while I am working on electrochemical assay development using SPEs and I noticed in many papers that the reference is an Ag Pseudo electrode or Ag/AgCl printed Pseudo...
05 June 2023 4,776 8 View
I need protein sequence data from the online gene essentiality database(OGEE) but the file that it put for download I don't get it. it's not a gene or protein sequence. I can find the sequence for...
11 January 2021 7,288 0 View
I have a heatmap and I want to assess the association of a nominal variant with the heat map data. What statistical test should I use? Thank you!
17 September 2018 1,596 7 View
We know that Aluminum has 8 series alloys and these alloys have a different composition. The effect of each of these elements on preparation (surface treatment as physically and as chemically) can...
05 March 2018 5,742 4 View
To enhance the properties of some polymers and give them a color, they use dispersion of pigments in polymer, which, if this dispersion happens well, can reduce the properties of the polymer....
05 March 2018 8,839 2 View
Hi everybody, I want to calculate reputation and trust based on direct information and witness information in my simulation. I was wondering if anyone has an experience about these two subjects....
26 May 2016 6,980 9 View
I need some FTIR instruments codes using for calculating Fourier Transformation by those instruments.
23 August 2015 813 3 View
I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?
11 August 2024 3,115 1 View
I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...
10 August 2024 4,005 2 View
Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...
09 August 2024 7,892 0 View
I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...
09 August 2024 5,048 2 View
I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...
08 August 2024 719 0 View
My name is Apurva Saoji. I am a Ph.D scholar in Computer engineering in India. I am looking for international expert in reviewing my PhD thesis, "Competitive Optimization Techniques to Minimize...
07 August 2024 4,600 2 View
Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...
06 August 2024 9,986 2 View
I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...
05 August 2024 454 3 View
I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...
05 August 2024 3,665 0 View
I am working on a SEM model where i have 7 latent variables (6 exogenous and 1 endogenous). In AMOS when I co-vary the exogenous constructs, only 2 paths are coming significant out of 6. But when...
03 August 2024 6,028 4 View